膛內時間 的英文怎麼說

中文拼音 [tángnèishíjiān]
膛內時間 英文
barrel time
  • 膛 : 名詞1. （胸腔） chest; thorax 2. （器物的中空部分） inside cavity; chamber
  • 內 : 名詞1. （內部; 里頭; 里邊） inner; inside; within 2. （妻子或妻子的親屬） one's wife or her relatives 3. （姓氏） a surname
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. In the paper, the projectile pushing process on firing is analyzed. the quantitative computational model of the projectile velocity to gun bore wear is built. finally, taking the 120mm gun for example, the relation of projectile velocity to gun bore wear is calculated, the phenomenon of trajectory peak is analyzed

    分析了射擊時彈丸擠進過程，建立了彈丸初速下降量與炮膛內膛磨損量計算模型，並以某火炮為實例計算了該炮彈丸初速下降量與炮膛內膛磨損量之間變化關系，分析了彈道峰現象，為身管壽命預測提供理論依據。
  2. These results show that since the existent defects of combustion device structure and its hypothetical circle of contact, these make a poor primary and secondary wind rigidity in operation and a too big actual circle of contact. in addition, the coal used is extreme prone to burn and reside in boiler. under such a condition, the coal powder ignites earlier in a short time and short distance when it leave the jet - combustioning device, and splashes the water cooler, eventually this results in a burned coal residue in boiler

    針對宏偉熱電廠410t / h燃煤鍋爐嚴重結渣問題，對燃煤的結渣性、爐內溫度工況及空氣動力工況等進行實驗研究，由於燃燒器結構和假想切圓選擇的缺陷，使得鍋爐在正常運行時，一、二次風剛性較差，實際切圓過大，加上目前燃用煤質屬于極易燃、易結渣煤質，致使煤粉在離開噴燃器很短的時間、較短的距離內開始著火，並沖刷水冷壁，最終造成爐膛結渣。
  3. It ' s necessary to measure and control the temperature of furnace. in the past, temperature instrument could only display the temperature of some points during heat treatment. however, it is needed to display temperature in the space of hearth. a new perfect system should be researched to measure and display the space temperature of hearth

    過去，對工件進行熱處理時，雖有溫度儀表指示控制溫度，但測溫儀表只能顯示某一點處的溫度，對于除此點之外的爐膛其他空間溫度則無法顯示並控制，而熱處理工藝所需要的卻是某一工作空間的溫度，這就要求研製一個更完善的系統，來進行爐膛內部溫度場的檢測和圖像顯示。
分享友人
分享到 Line

分享到臉書