膠體磨 的英文怎麼說

中文拼音 [jiāotǐmó]
膠體磨 英文
colloid grinder
  • 膠 : Ⅰ名詞1 （某些具有黏性的物質） glue; gum 2 （橡膠） rubber 3 （姓氏） a surname Ⅱ動詞（用膠粘） st...
  • 體 : 體構詞成分。
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  1. The big dipper colloid mill principle of work full sound of something astir grinding pan tooth profile incline relative motion but becomes, high speed revolves, another static causes the material to receive the enormous shearing force and the friction force through tooth profile incline between material, at the same time and so on under the complex strength function causes the material for the fluid ultramicron smashing, the emulsification, the disperser, isotropically at the high frequency vibration and the high speed whirlpool, to stir and so on the function, may replace and surpass the stone mill, the sand blast machine, the ball mill, the breast is uniform machine, cuts the mulser, three rollers machine, organizes working efficiency and so on the stamp mill

    七星膠體磨工作原理充分動靜磨盤齒形斜面的相對運動而成，其中一個高速旋轉，另一個靜止使物料通過齒形斜面之間的物料受到極大的剪切力和摩擦力，同時又在高頻震動和高速旋渦等復雜力的作用下使物料為流體超微粒粉碎、乳化、分散、均質、攪拌等功能，可代替並優于石磨，砂磨機、球磨機、乳勻機、剪切乳化機、三輥機、組織搗碎機等工作效率。
  2. Seven stars colloid mill principle of work full sound of something astir grinding pan tooth profile incline relative motion but becomes, high speed revolves, another static causes the material to receive the enormous shearing force and the friction force through tooth profile incline between material, at the same time and so on under the complex strength function causes the material for the fluid ultramicron smashing, the emulsification, the disperser, isotropically at the high frequency vibration and the high speed whirlpool, to stir and so on the function, may replace and surpass the stone mill, the sand blast machine, the ball mill, the breast is uniform machine, cuts the mulser, three rollers machine, organizes working efficiency and so on the stamp mill

    七星膠體磨工作原理充分動靜磨盤齒形斜面的相對運動而成，其中一個高速旋轉，另一個靜止使物料通過齒形斜面之間的物料受到極大的剪切力和摩擦力，同時又在高頻震動和高速旋渦等復雜力的作用下使物料為流體超微粒粉碎、乳化、分散、均質、攪拌、混合等多種功能，可代替並優于石磨，砂磨機、球磨機、乳勻機、剪切乳化機、三輥機、組織搗碎機等工作效率。
  3. We can obtain s the significance result. in this proces 1. co _ 2z ferrites obtain the quite good performance. in use second ball grindings in the gelatin spontaneous combustion method foundation to add bi2o3 agglutinates in the low temperature sinter

    在此過程中得到一些有意義的結果: 1在凝膠自燃法的基礎上，採用二次球磨加bi2o3的方法可獲得性能較好的低溫燒結co _ 2z鐵氧體。
  4. Seven stars big dipper multi - purpose colloid mill jm series, the colloid pump the zb series, the mulser r series

    產品描述:七星jm多功能膠體磨系列、膠體泵zb系列、乳化機r系列。
  5. An excellent adhesive was prepared from bismaleimide ( bmi ), epoxy resin ( e - 51 and tde - 85 ), 4, 4 ' - diaminodiphenyl sulfone ( dds ) in this thesis. the influence of liquid rubber and polymer ether imide ( pei ) on the properties ( especially high - temperature strength and the peeling strength ) were discussed, their different toughening characteristics and mechanisms were discussed. last, the process and effection of heat - resisted structural adhesive were studied by adhesive experiment of synchronizer in automobile. the results of investigation made clear : the adhesive, has good properties, especially heat - resisted properity

    根據材料分子設計的原理，研究了二苯甲烷雙馬來酰亞胺（ bmi ） 4 ， 4 』 ?二胺基二苯基碸（ dds ） e ? 51 tde ? 85組成的環氧膠粘劑體系，研究該體系在作為高溫結構膠粘劑使用時的粘接性能；然後研究了用無規羧基液體丁腈橡膠（ ctbn ? x ）和聚醚酰亞胺（ pei ）分別來增韌該體系的增韌效果；最後通過碳纖維耐磨材料與同步器圓錐環的粘接實驗，研究了耐高溫結構膠粘劑的粘接工藝和使用效果。
  6. The porous ceramics is composed of lots of bridge arch - shaped microspores that connected and well - distributed inside the material. when the fluid passes through these pores, the suspended matters, colloid particles and big molecular organic substances are withheld or absorbed to the inner surface of the pore, and result in filtration, purification adn even - dispersion, high strength, good resistance to abrasion, high temperature and corrosion, no pollution, long workinglife, and easy to regenerate, the porous ceramics are available for filtration and fluidization of variou gas and liquid

    微孔陶瓷過濾介質由許多大小分佈均勻，相互連通的橋拱狀開口氣孔組成.當流體從這些氣孔中通過時，流體中的懸浮物質，膠體顆粒，大分子有機物等被截留，吸附在微孔道內，從而達到了凈化和過濾均勻化的效果.微孔陶瓷強度高，耐磨損，耐高溫，耐腐蝕，無污染，氣孔分佈均勻，使用壽命長且再生簡便，特別適用於各種氣，液過濾和流態化過程
  7. The grade composite, road performance and its mechanism are systemically studied. 1 ) the aggregate grade of ogfc is studied through the volume method base on the analysis of the aggregate grades. then the grade is verified and the relation between the grade and pore rate is studied statistically, the typical grades of ogfc are developed ; 2 ) the reasonable pore rate of ogfc is studied on the basis of the balance of mechanics and function performance ; 3 ) the mineral fiber is added to the ogfc mixes to increase asphalt content, thus the anti - water performance of ogfc mixes are improved ; 4 ) high viscous asphalt fit for the preparation of ogfc is prepared through composite modification by sbs and rubber powder ; 5 ) the mechanics mechanism of ogfc is studied in the paper, it shows : asphalt paste, as well as the coarse aggregate skeleton, is essential to the mechanics of ogfc

    在分析各國ogfc級配的基礎上，運用礦料體積法進行ogfc級配設計，用正交實驗對礦料級配進行了優化設計，運用數理統計方法分析礦料級配和孔隙率之間的關系，並回歸出礦料關鍵篩孔通過率與ogfc骨架空隙結構關系的數學方程，進而提出了ogfc的合理級配；通過對不同孔隙率典型級配混合料的性能研究，綜合力學和功能性能，得出了ogfc的合理孔隙率范圍：針對高速公路面層對ogfc力學性能方面的要求，本文從瀝青膠結材料、纖維穩定劑兩方面對ogfc的性能進行改善：通過sbs和橡膠粉復合改性的方法開發出了適合ogfc的高粘度改性瀝青，摻加聚合物纖維，提高ogfc的最佳瀝青用量，進而改善了混合料的高溫性能和抗水損害性能，優化設計出能滿足高速公路路用性能，車轍動穩定度達5000次/ mm以上，動融劈裂強度比90 ，透水系數31ml / s ，並具有防滑降噪功能的開級配瀝青磨耗層（ ogfc ）混合料。
  8. The activity area of sediment and solution in gooey is distributary river, which has gigantic water power, good degree of sorting and roundness, gruff grain. lower mud and mica content

    分流河道的主體部位水動力較強，分選性和磨圓度較好，粒度粗，雲母礦物和泥質含量較低，是膠結物沉澱和溶解的活躍區，因而也是物性相對較好的地方。
  9. By physical and chemical testing and comprehensive analysis, it is suggest that deposited sands and rubber relics lead to local clogging of the pipe, so vortex around the clog lead to erosion abrasion

    通過理化試驗和綜合分析后認為，海水中沉積的泥砂和管內橡膠殘片集結成一體，對傳熱管形成局部阻塞，水流在阻塞物周圍產生渦流，發生沖蝕磨損，造成鈦管泄漏失效。
  10. The paper validates and perfects the traditional wear theory by using the ferrography, at the same time, combining the practice, mechanical embedded minor particles, scoring, plastic distortion, shaping effect and fatigue effect are analyzed and the results show that the vehicle ' s malfunction can be predicted

    文章作者將鐵譜磨粒分析技術運用在汽車維修行業，驗證和完善了傳統磨損理論，並結合實踐，對微凸體機械嵌合、膠合，塑料變形及刨削作用和疲勞作用進行了分析，證明汽車機械故障可以預測，且可以防止重大事故的發生。
  11. The tlow distance and gelating time of the nanocomposites were shorter than that of the pure pf, which meet the standard of the pf used in frictional materials. compared to the pure pf, the silica7pf nanocomposites exhibited excellent heat stability only in nitrogen atmosphere, however, so do vermiculite / pf nanocomposites in both nitrogen and air atmospheres. compared to the brake pad based pf resin, the wear rate of the present one based with silica / pf nanocomposite decreased obviously, especially in high temperature

    用烷基銨ctab和kh - 560對蛭石進行有機化處理，通過原位聚合法制備了酚醛樹脂接枝改性sio _ 2納米復合材料、酚醛樹脂kh - 560改性sio _ 2納米復合材料、酚醛樹脂ctab改性蛭石納米復合材料、酚醛樹脂/ kh . 560改性蛭石納米復合材料，採用ftir 、 xrd 、 afm和tg分析與流動距離、凝膠化時間的測試，研究了所制備的酚醛樹酯納米復合材料的結構、固化行為和熱穩定性能，並研究了以酚醛樹酯納米復合材料為基體的剎車片摩擦磨損性能。
  12. Roller 15 is integrated casting after processing, axiality between the two ball tracks is high with good connection with supporting roller. driving is stable and can lessen abrasion of cast rubber layer of supporting roller

    為整體花藍式鑄件，經加工製成，兩條滾道間的同軸度高，與托輥接觸良好，傳動平穩，且減少托輥鑄膠層的磨損。
  13. Taking gear without tooth face invalidation such as agglutination and abrasion as a precondition, and according to the relation between minimal oil film thickness and tooth face roughness of elastic liquid dynamic pressure lubrication theory, viscosity of gear lubrication oil was educed by reliability method in this paper, and the calculation formula has been elicited and applied

    摘要以齒輪傳動不發生膠合、磨損等齒面失效為前提，根據彈性流體動壓潤滑理論的最小油膜厚度與齒面粗糙度的關系，用可靠性方法確定齒輪潤滑油的粘度，給出計算公式並進行了實例計算。
  14. However, as more nano - zno was added and the smaller the particle size was, the shorter the vulcanization time was. on the other hand, when commercial zno powder was insteaded by nano - zno, the mechanic properties would be improved and the needed quantity of zno would be decreased. compared with rubber composites with 5 parts of commercial zno powder, rubber composites with only 1 parts of nano - zno have better mechanic properties, wear - resistance and anti - aging ability

    用幾種不同粒徑的納米氧化鋅取代普通氧化鋅，應用於以nr - br - sbr為基體的橡膠復合材料中，研究了不同粒徑的納米氧化鋅對橡膠復合材料硫化時間、常規力學性能、耐老化性能及摩擦磨損性能的影響並與加入普通氧化鋅的傳統橡膠體系進行了l廠b文通人學顧咐穴生學位淪義摘羅比較。
  15. Colloid mill is an excellent mechanical equipment for the fine process of wet particulates and widely used for food, pharmacy, chemical industry, daily chemical, construction material, emulsified asphalt etc

    膠體磨是濕式微粒化精細化加工的優秀機器設備，廣泛應用於食品制藥、化工、日用化學、建材、乳化瀝青等行業。
  16. Then, we utilized the additives of - al _ 2o _ 3 powder seeding, alumina sol seeding, tio _ 2 - sol, ammonium nitrate, and high - energy ball milling on the precursors to investigate these factors " influences on the transformation temperature, the microstructure of as - received nano - sized - al _ 2o _ 3 powders and transformation sequences

    接著，就分別研究在前驅體中加入或摻雜q - al _ 2o _ 3粉體籽晶、氧化鋁膠體籽晶、 tio _ 2溶膠、硝酸銨以及高能球磨前驅體等一系列因素對相變溫度、最終產物微結構、相變過程等的影響。
  17. Smooth surface colloid mill

    光面膠體磨
  18. General specification for colloid mill

    膠體磨通用技術條件
  19. Especially, overall stainless steel each colloid mill has the chinese invention patent and so on many items, are the domestic origination, the contour novel, environmental protection energy conservation, volume small, the benefit higher characteristic, lets your system reliably, is more static, saves the electricity

    尤其，整體不銹鋼各型膠體磨擁有中國發明專利等多項、屬國內首創，外形新穎，環保節能，體積小，效益高等特點，讓你的系統更可靠，更靜，更省電。
  20. Fluid friction, less wear of belt, service life being as fitted with safe protection device

    流體摩擦，膠帶磨損小，壽命提高一倍。
分享友人
分享到 Line

分享到臉書