自熱壓出法 的英文怎麼說
中文拼音 [zìrèyāchūfǎ]
自熱壓出法
英文
autothermal extrusion-
The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed
研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。Using the home made device, the relationship between the 3 voltage and the heating frequency is obtained by lock - in amplifier, thus the thermal conductivity of the fluid is calculated with the least square fit method
自行研製了流體導熱系數的測量裝置，採用鎖相放大器獲取3電壓與頻率的關系，並藉助最小二乘法，算出待測試樣的導熱系數。Deduces theoretically the natural ventilation calculation under the action of thermal pressure and wind pressure individually and simultaneously
從理論上推導出熱壓、風壓以及二者共同作用下的自然通風計算方法。Hot - press is a device of industrial manufacture designed to heat and press the workpieces. we designed this control system to fit the hot - press. its center unit is 89c55 single - chip microcontroller, and its output interface is a color lcd ( liquid crystal display )
熱壓機是一種對工件加熱加壓的工業生產設備，我們設計的與熱壓機配套的控制系統，以89c55單片機為中心器件，選用了彩色液晶顯示屏作為輸出界面，實現了按工藝參數的自動運行，用改進的pid演算法對溫度和壓力實現了良好的控制，並具有快捷有效的pid參數自整定的能力。分享友人