蒙皮材料 的英文怎麼說

中文拼音 [mēngpícáiliào]
蒙皮材料 英文
skin material
  • 蒙 : 蒙名詞（蒙古族） the mongol nationality
  • 皮 : Ⅰ名詞1 （人或物體表面的一層組織） skin 2 （皮革） leather; hide 3 （毛皮） fur 4 （包在外面的一層...
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. These advantage make it excellent materials for control surface, wing and skin of airplane

    是飛機結構中對剛度要求較高的操縱面、機翼和機身蒙皮結構用較理想的材料。
  2. The large - scale honeycomb structure, an important component of the last stage fuel tank of launch vehicles, is composed of the honeycomb sandwich and thin aluminum alloy sheets with ellipsoid shape

    大型蜂窩共底構件是液體運載火箭末級推進劑箱的一個關鍵部件，它是由蜂窩夾芯復合材料和上、下薄鋁合金蒙皮粘接固化而成的。
  3. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  4. In the formula, our experience in structural strength design and the experimental results are considered. and such factors are also considered as differences in materials of the skin and the reinforcer, effects of bending, torsion, stretching and offcenter of the reinforcer. furthermore, through post - buckling stress analysis of the skin, it is shown that even low stress level will result in buckling of the skin, but the skin still has loading capacity

    在總結過去結構強度設計和試驗分析的基礎上，應用扁殼理論，在廣義力與廣義應變關系中考慮了蒙皮與加筋不同材料以及加筋的彎曲、扭轉、伸縮和偏心等的影響，推導出適合於工程應用的加筋殼結構軸壓屈曲臨界載荷的計算方法;並通過對薄壁結構蒙皮后屈曲應力分析，說明蒙皮在很低的應力水平時就出現失穩現象，但失穩后的蒙皮仍具有一定的承載能力。
  5. Concerning the tests, analyses, design and calculation of performances for light gauge steel framing, this paper focuses on following items : ( 1 ) the calculation of light gauge steel framed compound bearing walls ( lgsfcbw ) in compression and bending. based on north american specification and commentary for the design of cold - formed steel structural members, which was published by the american iron and steel institute, the detailed design requirements of wall stud assemblies are given considering the structural contribution of the attached sheathings and shear diaphragm is discussed briefly. then the calculational theoretic and method for sheathing braced wall stud assemblies complying with national code is brought up in compression and bending

    本文圍繞輕鋼龍骨體系結構性能的試驗、分析、設計和計算，主要進行了以下四方面的研究工作： （ 1 ）輕鋼龍骨復合承載墻體的受壓、受彎計算：以美國鋼鐵協會發行的北美冷成型鋼構件設計規范及其規范說明為依據，重點考慮罩面材料對墻龍骨設計的影響，給出了目前對承重墻龍骨設計的具體要求，並對剪力蒙皮進行了簡要討論；然後提出了符合我國規范術語的剪力蒙皮作用的輕鋼龍骨復合承載墻體（即罩面支撐墻龍骨）受壓、受彎的計算理論和方法；最後對提出的計算進行簡化，使之完全與我國規范相符。
  6. In case of consulting the experiment standard of skin diaphragms connection at abroad, through 20 experimental research and data analysis, it understands tentatively the destruction modes of the jointing connected by self - drilling screws, has also understanded the performance of the self - drilling screws

    在參照國外蒙皮連接試件實驗標準的情況下，通過20個試件的試驗研究和數據分析，初步了解自攻螺釘連接件的破壞模式，提出了自攻螺釘的實際材料性能指標。
  7. The selection of material, typical the structural designs, the mechanical property and the forming pressure of unmanned aircraft sandwich composite material have been studied in this paper. it has analysed and discussed the flexural properties of honeycomb sandwich plate delamination under bending loads in detail. and then the mechanical properties of the laminate panel are studied which are compared with honeycomb sandwich panel

    在圍繞某無人機蒙皮選用材料的基礎上，重點對蜂窩夾層結構的結構設計、力學性能、成型壓力對力學性能的影響，以及缺陷對蜂窩夾層結構復合材料的彎曲性能影響進行了較深入的實驗研究和理論分析，同時比較了蜂窩夾層結構中面板與同樣材料鋪層的疊層板力學性能的差異。
  8. In upper level optimization, the thickness and geometry factors of composite skins and webs as well as other structural dimensions are taken as design variables. then, considering the behavior constraints and the side constraints, the structural mass is minimized by the mathematical programming technique. in lower level optimization, the mathematical programming technique or the genetic algorithm ( ga ) is used to search the practical stacking sequence of composite skins and webs to realize the given thickness and geometry factors from upper level optimization

    底層優化設西北工業大學博士學位論文計以復合材料蒙皮和腹板等層合板各分層的厚度（或鋪層數） 、鋪層角和鋪層順序為設計變量，以層合板的幾何因子與頂層優化設計給出的最優幾何因子之間的誤差最小為目標，考慮層合板厚度和製造工藝性約束，採用數學規劃方法或遺傳演算法（ geneticalgorithm ，簡稱ga ）求出底層最優設計變量。
分享友人
分享到 Line

分享到臉書