蓋上閥 的英文怎麼說
中文拼音 [gěshàngfá]
蓋上閥
英文
valve in head-
Install a minimum of 1 " above flood level of fixture if factory deck mounted or not less than 6 " if general plumbing field application
安裝時要使閥蓋側面朝上,要便於測試和維修。不要安裝在隱蔽的位置或區域,在這些地方,由於閥內件正常磨損產生的水泄漏可能導致閥門損壞。Reciprocating internal combustion engines. designation of the direction of rotation and of cylinders and valves in cylinder heads, and definition of righ - hand and left - hand in - line engines and locations on an engine
往復式內燃機.氣缸和氣缸蓋上閥門旋轉方向標志及右側發動機和直列式發動機的定義,以及在發動機上的定位Remove the bolts and cover, realign the diaphragm assembly, and place the cover back on the relief valve body
拆卸螺栓和閥蓋,重新校準隔膜總成,並將閥蓋放回到安全閥閥體上。Body / bonnet joints on pacific valves are designed for rugged services with a more than adequate number of bonnet bolts
美國太平洋閥門上的閥體/閥蓋連接結構適用於惡劣的應用環境,可配置足夠數量的閥蓋螺栓。Disconnect the hose from the bottom cover plate to the relief valve
斷開底部蓋板到安全閥上的軟管。Place the cover onto the spring with the internal guide on the cover positioned inside the end coil
將閥蓋及閥蓋上的內部引導放置在彈簧上,定位內部端線圈。Holding the memory stops in position, turn the ( clockwise ) down until it stops against the valve bonnet. the memory has now been set
將記憶止動裝置保持在其位置上,順時針旋轉鎖軸環直到其停止靠到閥門閥蓋為止。記憶現在已經設置完畢。To clean : inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs
清洗:檢查或更換磨損的閥門閥瓣,斷開控制管道,用鈍工具和錘打閥蓋塞頂部,從閥體上旋下閥蓋。Place the cover o - ring on the diaphragm assembly
將閥蓋o形環放置在隔膜總成上。Straight moving type relief valves, mainly valve disc, valve body, spring - loaded, roof, regulation pole, conditioning nut, and other integral parts
直動型溢流閥,主要有閥芯、閥體、彈簧、上蓋、調節桿、調節螺母等零件組成。The stem and diaphragm assembly will normally remain with the cover as it is removed
閥桿和隔膜總成通常附在閥蓋上與閥蓋一起拆離。Auxiliary equipment. cooking. heating. push - on connectors for rubber tubes and caps intended to be fitted on certain domestic appliances using mains distributed combustible gases and on g 1 2 b male wall - mounted taps
輔助設備.烹調.加熱.使用管道供燃氣的某些家用設備上安裝的橡膠管件和密封蓋的推入式連接器和g1 2陽螺紋墻裝氣閥的連接器Service of all internal check valve components shall be through top mounted access covers threaded to the main valve body
所有止回閥內部部件的維修應該能夠通過頂部安裝的檢修蓋進入進行,這種檢修蓋應該通過螺紋固定在主閥門閥體上。The lid of this sterilizer is installed with safety valve, exhausting valve, exhausting valve which can keep safety
滅菌器蓋上裝有安全閥、放汽閥和壓力表,能有效釋放過高壓力,確保安全可靠。放氣閥尾部備有金屬軟管,使排放冷空氣合理方便。Extending extension lead
延伸型上閥蓋Repeat steps 2 - 5 until proper sag is achieved, then replace the air valve cap
重復2 5步驟以達到最佳預壓行程后,蓋上氣閥嘴帽。For assembling the bonnet and valve body, be sure that screws, nuts and washers shall be tightened up evenly
上蓋與閥體的組裝將4根螺絲,螺母及華司平均的鎖緊。Add protective cap over electrical connector, set suction lever to full open
把聯線端的保護帽蓋上,把吸引閥開到最大位置。Valves with hose union ends shall be complete with hose union and washer fitted to the seat retainer and screwed “ [ red ] finger tight [ / red ] ” only
帶有用於軟管連接的端面的閥門,應將軟管連接器和墊圈裝配在閥蓋上,並旋入到手指能撥動的程度即可。[ br ] valves with hose union ends shall be complete with hose union and washer fitted to the seat retainer and screwed “ [ red ] finger tight [ / red ] ” only
帶有用於軟管連接的端面的閥門,應將軟管連接器和墊圈裝配在閥蓋上,並旋入到手指能撥動的程度即可。分享友人