蝸輪傳輪比 的英文怎麼說
中文拼音 [lúnzhuànlúnbǐ]
蝸輪傳輪比
英文
worm gear ratio-
On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency
從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3
通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error
摘要針對圓筒型照相排版機底片掃描裝置要求傳動精度高，轉動平穩的特點，分別選擇三級圓柱齒輪傳動，雙級圓柱齒輪蝸桿傳動，蝸桿傳動3種常見的傳動方式，計算其傳動比，驗算傳動精度，對掃描裝置進行運動精度分析，計算總體傳動誤差。Cylindrical worms ; dimensions, correlation of shaft centre distances and gear ratios of worm gear drives
圓柱形蝸桿.尺寸軸心距和蝸輪傳動傳動比之間的關系The motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given
本論文主要包括以下內容：介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系，分蝸桿固定和定子固定兩種情況，給出了這種新型傳動的傳動比計算公式，得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系，從而為該傳動的優化打下理論基礎。Besides the routine characteristics, xs series worm gear units adopts the helical gear - worm wheel type to make the structure more reasonable. the series not only has higher transmission efficiency and loading capability than those of single - stage worm wheel transmission, but also reduces space. moreover, under the close volume, the series can obtain higher transmission ratio and is more favorable for equipment setting
Xs系列蝸輪蝸桿減速機除具有常規特性外，該機還採用了斜-蝸輪形式，使結構更加合理化，它不僅改變了比單級蝸輪蝸桿傳動具有更高的傳動效率和承載能力，而且在結構布局上縮小了空間佔地面積，同時在相近體積條件下，能獲得更大傳動比，更有利於設備的配置，該機能與各種減變速機組合，滿足不同的使用要求。5 design for small gear relates to hatch size of control - pan -, worm - wheel ratio and fact abrasion quantum of brake block. this article gives their compute formula
5小齒輪的設計與控制盤開口尺寸、蝸輪蝸桿的傳動比和制動襯片的實際磨損量有關，文中給出了它們的計算公式。Abstract : the paper suggests two methods for adjusting the mesh clearance in cylindrical worm drive : one is to adjust the meshing center distance of worm gears, the other is to use dual lead cylindrical worm, introducing briefly the principle of adjustment and making a comparison between the characteristics of the two methods
文摘:提出了兩種調整圓柱蝸桿傳動嚙合側隙的方法:通過改變蝸輪蝸桿的嚙合中心距來改變其嚙合側隙;採用雙導程蝸桿傳動以調整蝸輪蝸桿的嚙合側隙，簡述了調整原理，並比較了兩種調整方法各自的特點。分享友人