螺栓固緊 的英文怎麼說

中文拼音 [luóshuāngùjǐn]
螺栓固緊 英文
bolt tightening
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 栓 : 名詞1. （可開關的機件） bolt; plug 2. （塞子） stopper; cork
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 緊 : Ⅰ形容詞1 （物體受到幾方面的拉力或壓力以後呈現的緊張狀態） taut; tight 2 （物體受外力作用變得固定...
  • 螺栓 : bolt; screw bolt; threaded bolt
  1. Bonded abrasive products. disc wheel with inserted nuts

    普通磨具.螺栓緊固平形砂輪
  2. The two locking bolts should be tightened first in order to position the flanges correctly as shown in fig. 1

    為了如圖1所示正確定位法蘭，應該首先緊固兩個鎖定螺栓。
  3. Fasteners. bolts for corrugated steel pipes. part 0 : bolts related prescriptions screws nuts

    緊固件.波紋鋼管用螺栓.第0部分:與螺栓有關的說明
  4. The main products range is various forged fasteners, pressed hardware and machining parts, inclusing non - standard bolt, high strength bolt, steel - strcture bolt, stude screws, double arming bolt, u - bolt or l - blot, tower bolt and other bolt, with hex head or square one according to the customer " s requirement

    該公司的主要產品為熱鐓成型的各種緊固件和五金沖壓件具體類型:高強度螺栓、鋼結構螺栓、普通外六角螺栓、內六角螺栓、地角螺栓、雙頭螺栓、 「 u 」或「 l 」型螺栓、電力鐵塔螺栓、鐵路道釘、高速公路護攔螺栓、油井上用的各種專用螺栓和汽車配件。
  5. Tightening inspection for through bolts of main engine ( m. e. )

    主機貫穿螺栓緊固度檢查。
  6. To irregular joints, fastness should start from bolts at assembly points to outside symmetrically

    對于不規則的接頭，應從拼接處的螺栓群對稱地向外側順序進行緊固。
  7. Repeat procedure with other body half and bolt together following the procedure noted above

    對另一半閥體重復同樣的步驟，然後按照上述步驟用螺栓緊固在一起。
  8. The lid was bolted down

    蓋子用螺栓緊固。
  9. Specification for the use of high strength friction grip bolts in structural steelwork - metric series - general grade

    結構鋼制構件高強度摩擦緊固螺栓應用規范，米制系列.第1部分:普通螺拴
  10. Specification for the use of high strength friction grip bolts in structural steelwork - metric series - higher grade parallel shank

    結構鋼制構件中高強度摩擦緊固螺栓應用規范，米制系列.第2部分:高級螺拴
  11. 396 after seven days, the grouted mortar will have concreted, then we shall tighten the anchor bolts

    灌漿在七天以後凝固，我們就將擰緊地腳螺栓。
  12. Holding down bolt

    固定螺栓，壓緊螺栓
  13. Gasket deforms during hydrotest, bolts lose torque and must be retightened after hydrotest. ( pressure / temperature transient or frequent cycling produces similar mechanical action in valve

    在水力測試時，墊圈會變形，螺栓松動，因此在水力測試后必須加以緊固。 （壓力/溫度轉換或周期循環在閥門上產生相似的機械作用。 ）
  14. Grip clamp with cushion fixed fland using single bolt and lightening hole

    帶減輕孔單螺栓側面固定夾緊卡箍
  15. Railway fixed equipment. rail screw - bolts

    鐵路固定設備.鋼軌用拉緊螺栓
  16. Fixed railway installations. equipment for overhead telecommunication and signalling lines. tie and bracing bolts

    鐵路固定裝置.通訊和信號裝置架空線路用器材.系緊和拉緊螺栓
  17. After proper operation has been verified, tighten all bolts using the crossover method. recommended tightening torques pattern is listed below

    在檢驗操作能夠正常進行后，在採用交叉法緊固所有螺栓。推薦的緊固扭矩模式如下所示。
  18. Steel bolts and nuts for fish - plates and fastenings

    魚尾板用鋼螺栓及螺母和緊固件
  19. Pressure seal design without live load bonnet ( no spring washers ) : the gasket bolt tightness must be rechecked after operating test pressure and temperature has been achieved

    沒有動負載閥帽的壓力密封結構（沒有彈簧墊圈） ：在工作試驗壓力和溫度達到限制值時，必須重新檢查墊圈螺栓的緊固性。
  20. Form ties bolt : 12 thin bolt use double nut for locking action, 16 wide bolt use 12 iron thread for locking to prevent release power after locking nut

    6對拉螺栓： 12細扣螺栓的緊固使用雙螺母， 16粗扣螺栓鎖母緊固後用12鐵線固定防止松動。
分享友人
分享到 Line

分享到臉書