螺桿傳動 的英文怎麼說
中文拼音 [luógǎnzhuàndòng]
螺桿傳動
英文
lead-screw drive-
The micromotion drive unit is a highly refined screw-driven hydraulic jack.
微形傳動裝置是一個極精製的螺桿用液壓作動筒。Abstract : the calculation of the rigidity for the ball screw transmission system was discussed, including the axial rigidity of the screw, the axial rigidity of supporting bearing, the contact rigidity between ball and groove. the influence of the rigidity variation on the transmission accuracy was analyzed
文摘:本文系統地討論了滾珠螺旋傳動系統的剛度計算,包括螺桿本身的軸向剛度、螺桿兩端支承軸承的剛度以及滾珠與滾道間的接觸剛度,並分析了剛度變化對傳動精度的影響。Thread forming and thread cutting tapping screws and metallic drive screws, inch series
自攻螺釘攻絲螺釘和金屬傳動螺桿Harmonized system of quality assessment for electronic components : sectional specification : lead screw actuated and rotary preset potentiometers
電子元器件用質量評估協調體系.分規范.導螺桿傳動和旋轉式預調電位器X axis and y axis adopt ball spiral rods with excellent precisions and low friction factors
X . y軸採用滾珠螺桿傳動精度佳,摩擦系數小。Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s
導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別sThe motion of the drive is also demonstrated. the paper mainly concludes the following works : the paper introduces the meshing theory of rolling cone - type toroidal drive and the motional relations of all parts, gives the formula of transmission radio. the relation between tooth numbers and helix angle of every parts is found out, and the assemble relation among all the parts is also given
本論文主要包括以下內容:介紹了超環面行星蝸桿傳動的傳動原理及各構件間的運動關系,分蝸桿固定和定子固定兩種情況,給出了這種新型傳動的傳動比計算公式,得出了各輪齒數與計算圓處螺旋升角間的關系和各構件間的裝配關系,從而為該傳動的優化打下理論基礎。This paper introduces the characteristic of these two types of driving mode, compares them from aspects of mounting, operation and maintenance, then comes to the conclusion that the belt motion will lead the development of automatic door
介紹了齒帶和螺桿兩種門傳動方式的特點,並從安裝、使用和維護的角度進行分析比較后認為,齒帶傳動是發展趨勢。Based on theory of gear driving, fluid mechanics, hydrodynamic lubrication, polymer rheology and single - screw extrusion, key structure design principles in melt pump are summarized, some theory foundations are also deduced
結合齒輪傳動、動力潤滑、流體力學、高聚物加工流變學以及單螺桿擠出理論的部分知識對熔體泵結構設計中的主要問題進行了總結,並對其中部分理論依據進行了推導。X, y axis drive with ball screw. mos - fet circuit design
Y軸均用滾珠螺桿,傳動輕巧,使用方便。Screw driving skylight controlling gear
螺桿式天窗傳動裝置Crank arm is the one of the important components of air compressor and bears the drastic dynamic load during its working prcess. and then the dynamic load is transfered to the bolts and the nuts connecting the crank arm body and the top
連桿是空壓機重要構件之一,其在工作過程中承受著急劇變化的動載荷,這一動載荷又傳遞到連桿體和連桿蓋的兩個連接螺栓及螺母上。This paper focus on the development of a kind of a reducer directly connected to the down hole progressing cavity pump. this development includes the selection of reasonable structure, designing, simulation, manufacturing and testing of the reducer which has the properties of high horsepower to weight ratio and compactness
本文針對螺桿泵採油生產中井下驅動螺桿泵採油系統需要的一種體積小、傳遞功率大的減速器為研究目標,對井下驅動減速器的類型選擇、結構設計、模擬、製造和實驗等進行設計研究。Screw and nut mechanism
螺桿螺母傳動機構The wall - tie is changeable by adjusting the thread rods, so it meets the needs of different wall - tie length at each section the max. length is 12m. its drivng device is provided with parallel two or three drives, and the cage can be with or without cabin for driver
附墻支撐具有可變段和螺桿調整,適應各道附墻長度不同的要求最大附墻距離12米,傳動機構有並聯雙傳動或三傳動兩種供貨形式,吊籠可以有駕駛室或無駕駛室。分享友人