螺紋彎 的英文怎麼說

中文拼音 [luówénwān]
螺紋彎 英文
threaded bend
  • 螺 : 1. [動物學] （軟體動物） spiral shell; snail; conch 2. （螺旋形的指紋） whorl （in fingerprint）
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  1. Round thread casing joint strength with combined internal pressure and bending

    內壓和彎曲復合作用下圓螺紋套管的連接性能
  2. Longitudinal crack formed when screw steel rebar is cold - bended was analyzed. the result indicates that ununiformly distributed silicate inclusions contributed to the longitudinal crack. protective measurements were also provided

    摘要對螺紋鋼筋由冷彎產生的縱向裂紋進行了分析，結果表明，硅酸鹽夾雜物分佈不均勻是造成螺紋鋼筋冷彎縱向裂紋的主要原因，並提出了相應的預防措施。
  3. In practical application, the m10 180 bolts, which are installed in the head cover of the torque divider of ts5560 special automobile, sometimes fracture all of a sudden. according to the tests of acceleration, stress and strain, and the exciting test, it is resonance vibration that leads to the compound - bending fatigue fracture of the bolts. the exciting force caused by drive system, transmitted through the torque divider, produces a 1000 - 1500hz cyclical excitation at the junction of the bolts and head cover, which causes the first order bending resonance vibration of the bolts

    通過加速度、應力應變測試實驗和激振試驗的研究，發現ts5560特種車分動器取力器氣缸端蓋m10 180螺栓斷裂問題是由於共振引起的雙向彎曲疲勞斷裂：傳動系統工作所產生的激勵，經過分動器結構的傳遞（特別是分動器一階扭轉模態的放大） ，在螺栓的連接處產生1000 1500hz的振動激勵，其導致螺栓一階彎曲共振，在螺栓一階彎曲模態的阻尼比較小的情況下，使得螺栓產生較大的共振響應，導致螺紋處的彎曲動應力較大，疲勞壽命較低。
  4. Roofing and wall cladding. fasteners. determination of the bending characteristic resistance. conventional test method for bending of self - drilling and self - tapping fasteners longer or equal to 70 mm

    屋面和墻壁覆面.緊固件.彎曲抗性的測定. 70mm及以上的自鉆和自攻螺紋緊固件彎曲性的常規試驗方法
  5. Specification for steel conduit and fittings with metric threads of iso form for electrical installations - steel conduit, bends and couplers

    電氣裝置用iso型米制螺紋鋼導管及接頭規范.第1部分:鋼導管彎頭和接頭
  6. Power overhead lines ; bent insulator spindles for screwing

    架空電力線.第3部分:螺紋連接用彎頭絕緣心軸
  7. Diaphragm type chemical seal, miniature diaphragm seal with process connection, process connection : thread, rigid or turning nipple

    迷你型膜片化學密封，帶有過程連接，過程連接為：螺紋筆直的或彎曲的接頭螺母。
  8. The geberit mepla range of fittings it includes among others straight connectors, elbows and tees, with male or female threads

    包括帶內螺紋和外螺紋的直接頭，彎頭和「 t 」型接頭等完整的管件。
分享友人
分享到 Line

分享到臉書