行鍵 的英文怎麼說

中文拼音 [hángjiàn]
行鍵 英文
line unit
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  1. Taper key torque transmission ; gib - head parallel keys, dimensions and application

    扭力傳動斜鍵.彎頭平行鍵.尺寸和應用
  2. Detail specification for short stroke keypads

    短行鍵區的詳細規范
  3. Soft error display complete. going to set keyboard typematic rate

    軟錯誤顯示結束。即將進行鍵盤擊鍵速度進行設置。
  4. Shell end mills with tenon and parallel key drive ; dimensions

    帶榫和平行鍵槽的筒形端銑刀.尺寸
  5. Firstly, the process was analyzed technically, a qualitative approach was used to identify critical events ( root causes )

    首先進行鍵合工藝技術分析，採用了一種定性方法來辨識故障。
  6. To review the current value of the code page, at the job level, you can issue the following from an os 400 command line

    為了在作業級查看代碼頁的當前值，您可以從os / 400命令行鍵入下列命令：
  7. Click on the lower right corner of start for key spaces, and then point the upper left corner, start the game started

    點擊右下角「 start 」 ，進行鍵位設置，再點左上角「 start 」開始游戲。
  8. Of object or row keys to be updated by the update operation

    更新操作要更新的對象或行鍵的
  9. Of object or row keys to be deleted by the

    操作刪除的對象或行鍵的
  10. Parameter represents the object or row keys of the data to update

    參數表示要更新的數據對象或數據行鍵。
  11. Parameter represents the object or row keys of the data to delete

    參數表示要刪除的數據對象或數據行鍵。
  12. Drive type fastenings without taper action - parallel keys - calculation and design

    無錐度連接的驅動式緊固件.直行鍵.計算和設計
  13. If the data is simple enough, this could be a comma, but more complex strings are usually separated using tabs, new lines or a combination of characters not likely to be found in the record itself

    如果數據簡單，分隔符可能是逗號，但更復雜的字元串通常用製表符，換行鍵或在記錄中未出現的字元組合來分隔
  14. Keying. assembly by means of parrallel keys. dimensions

    鍵連接.通過平行鍵組裝.尺寸
  15. Requires a comparer implementation to perform key comparisons

    需要比較器實現來執行鍵比較。
  16. Three - row keyboard

    三行鍵盤
  17. To rebuild the assembly module, change your directory to geronimo modules assembly and type

    要重新構建程序集模塊，請將目錄更改為geronimo / modules / assembly ，並在命令提示行鍵入
  18. When typing a j class name or keyword, you have a choice : you can either type the complete word yourself, or let the intellisense tool that is part of the code editor

    鍵入j #類名或關鍵字時，您可以選擇：自行鍵入完整的單詞，或者讓intellisense工具（ 「代碼編輯器」的一部分）幫您完成。
  19. Taper key torque transmission ; parallel keys, dimensions and application

    錐形鍵扭距傳輸.平行鍵.尺寸和應用
  20. If the full lock cannot be acquired, no lock escalation happens at that time and the database engine will continue to acquire row, key, or page locks

    如果無法獲取全鎖，當時不會發生鎖升級，而數據庫引擎將繼續獲取行、鍵或頁鎖。
分享友人
分享到 Line

分享到臉書