裂化系數 的英文怎麼說

中文拼音 [lièhuàxìshǔ]
裂化系數 英文
factors of cracking
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained

    本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。
  2. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  3. Abstract : 145 samples of eight plants were collected from lanmuchang and yangjiawan and quantitative analyses were made of the ore - forming elements in the plant ashes. considering the three principles of the plant indicator for mineral exploration, namely certainty, sensitivity and feasibility, this paper evaluates comprehensively the indicating functions of the eight plants, on the basis of some quantitative indexes such as the relation coefficient between plant ash and ore - forming element, concentration coefficient, etc. it also discusses the relationships between the anomaly of plant ashes and the fault zone, alteration zone mineralization zone and orebody, showing the significance of these plants to the prospecting

    文摘:在濫木廠和楊家灣鉈（汞）礦床（點）對芒箕、南燭、榔榆、大金發蘚、蜈蚣草、石松、黃花草、醉魚草等8種植物取樣145件，在提出確定找礦有效指示植物三原則（確定性，敏感性，可行性）的基礎上，依據植物灰分與底質成礦元素相關系數、植物灰分富集系數和襯度系數，較全面地分析和評價了8種植物的找礦功能；討論了其異常的分佈與斷裂帶、蝕變帶、礦化帶以及工業礦化（礦體）之間的關系，並指出了其找礦意義。
  4. Several materials with large coefficient of expansion were selected to make packaging components, and it was found that the packaging materials have good temperature sensitivity and compatibility with optical fibers. experimental accuracy and repetition of fbg temperature sensitivity and compensation were discussed. have selected several materials which has bigger coefficient of expansion to do packaging components, have made many temperature experiments, there have not flaws, such as aging, crackle, absciss layer, packaging materials have good temperature sensitivity and compatibility with optical fiber ; have designed the simple and practical packaging components, have performed a serials of experiments about accuracy and repetition of fbg wave - length, have obtained the first step conclusion ; have analyzed the result and made comparison between the result of different experiment, have summarized the best packaging effect and several rules to reduce mistskes

    本文所做的主要工作包括以下幾個內容：一、選取了常見的熱膨脹系數大的材料製作封裝元件，經過多次一80到80反復測試，封裝元件沒有出現老化開裂、封裝裂紋、空洞、離層等缺陷，封裝材料具有良好的溫敏穩定性及復用性，與光纖相容性較好；二、對光纖光柵進行簡單、實用的封裝處理，就封裝效果的優劣性、波長測量的準確度、重復性和封裝時產生的波長損失等方面進行了一系列的實驗，得出了初步的結論；三、對溫敏和溫度補償式封裝的實驗數據進行了詳細的分析和對比，從數字上對溫變過程中光纖光柵中心波長的改變及溫變曲線進行了定量的分析，在大量實驗數據分析結果的基礎上，總結出哪種材料封裝效果更好，以及如何有效的減小實驗誤差。
  5. It is found that the degree of mineralization and metamorphic coefficient and conversion potential of formation water, the fault is zone of sluicing of atmospheric infiltration water flowing from basin west margin to east ( centripetal flow ) and sedimentary compaction water flowing from qija gulong depression to west ( centrifugal flow )

    通過地層水礦化度和變質系數等參數的分佈規律及一系列折算水位剖面圖的分析發現，該斷裂對水是不封閉的，並且是盆地西緣大氣滲入水向東流動（向心流）及齊家古龍坳陷沉積壓實水向西流動（離心流）的共同泄水帶。
  6. The grade composite, road performance and its mechanism are systemically studied. 1 ) the aggregate grade of ogfc is studied through the volume method base on the analysis of the aggregate grades. then the grade is verified and the relation between the grade and pore rate is studied statistically, the typical grades of ogfc are developed ; 2 ) the reasonable pore rate of ogfc is studied on the basis of the balance of mechanics and function performance ; 3 ) the mineral fiber is added to the ogfc mixes to increase asphalt content, thus the anti - water performance of ogfc mixes are improved ; 4 ) high viscous asphalt fit for the preparation of ogfc is prepared through composite modification by sbs and rubber powder ; 5 ) the mechanics mechanism of ogfc is studied in the paper, it shows : asphalt paste, as well as the coarse aggregate skeleton, is essential to the mechanics of ogfc

    在分析各國ogfc級配的基礎上，運用礦料體積法進行ogfc級配設計，用正交實驗對礦料級配進行了優化設計，運用數理統計方法分析礦料級配和孔隙率之間的關系，並回歸出礦料關鍵篩孔通過率與ogfc骨架空隙結構關系的數學方程，進而提出了ogfc的合理級配；通過對不同孔隙率典型級配混合料的性能研究，綜合力學和功能性能，得出了ogfc的合理孔隙率范圍：針對高速公路面層對ogfc力學性能方面的要求，本文從瀝青膠結材料、纖維穩定劑兩方面對ogfc的性能進行改善：通過sbs和橡膠粉復合改性的方法開發出了適合ogfc的高粘度改性瀝青，摻加聚合物纖維，提高ogfc的最佳瀝青用量，進而改善了混合料的高溫性能和抗水損害性能，優化設計出能滿足高速公路路用性能，車轍動穩定度達5000次/ mm以上，動融劈裂強度比90 ，透水系數31ml / s ，並具有防滑降噪功能的開級配瀝青磨耗層（ ogfc ）混合料。
  7. Tar content in the gas was influenced by the gasification conditions, such as the gasification temperature, residence time of feedstock in the gasifier and the type of feedstock, which can help us to investigate the mechanism of tar production in gasification process. catalytic cracking of tar was performed in a downstream secondary fixed - bed cracker with dolomite, limestone and alumina brick as catalysts. by comparison, thermal cracking of tar was also performed with silica carbide

    在固定床二級催化裂化反應器上，實驗了白雲石、石灰石、高鋁磚等幾種催化劑作用下的焦油催化裂化過程以及炭化硅作用下的熱裂化過程，並對裂化溫度（ 650 950 ） 、氣相停留時間（ 0 . 5 1s ）和催化劑類型等過程參數對焦油轉化效果和熱解煤氣的影響進行了分析，對各種催化劑材料的性能進行了比較，力爭開發出可適用於工業化生物質氣化系統的焦油催化裂化技術。
  8. The contents of this paper include the following several aspects : ( 1 ) a model of the fractures leakage is built through counting and analyzing the wealthy geological records of hae field, and a model of the fracture water transporting is also built according to the fracture water condition of its recharge and its runoff and its discharge in hae field ; ( 2 ) this paper studies the chemical behavior and the migration parameters of the elenent sr2 + in ground water in hae field, the main contents include : the presence form of the element sr in ground water is analyzed by way of the rmodynamics ; the absorption mechanism that granite and sand stone absorbs sr element is analyzed based on theory and experiment test the diffusion parameters of the element sr in water and in granite and in sand stone are researched with laboratory experiment test ; the partition coefficient of sand stone and granite to sr is tested by the batch way

    其研究內容包括以下幾個方面： （ 1 ）通過對我國hae預選處置場豐富地質資料的大量統計和分析，建立了該處置場的基巖裂隙滲透模型。再根據hae預選處置場基巖裂隙水的補給、徑流、排泄條件及水位動態特徵，建立了預選處置場基巖裂隙水水運動模型。 （ 2 ）對高毒性鍶元素在我國hae預選處置場地下水中的化學行為和遷移參數進行系統的研究，其中主要包括運用熱力學方法分析了鍶元素在地下水中的存在形態，利用理論分析與實驗測試相結合的方法分析了花崗巖和砂巖對核素鍶的吸附機制，採用室內實驗裝置研究了核素鍶在地下水中的擴散參數以及在花崗巖和砂巖中的本徵擴散參數，採用靜態批式法研究了鍶在砂巖和花崗巖中的分配系數。
  9. And the choice range of hydration coefficient is determined on calculating mass concrete of foundation in high - rise building. at last, combining the test data with the ansys result, some measures about crack - control in construction are summarized. it can be referred to the study on mass concrete of foundation in high - rise building for interaction between concrete temperature field and soil temperature field considered, choice range of hydration coefficient determined, and measures about crack - control in construction summarized in this paper

    最後，結合現場監測的數據和ansys計算的理論值，對高層建築基礎大體積混凝土的溫度裂縫的控制提出了有效的控制措施本文提出考慮混凝土與土壤相互作用的溫度場，確定的高層建築基礎大體積混凝土溫度場計算時的水化系數的取值范圍以及建議的現場溫度裂縫的控制措施，對今後建築工程大體積混凝土的研究具有一定的參考價值。
  10. This thesis first describes the general research development of bp network, kde, genetic algorithm, arx model and their specific application in dms such as architecture, algorithm - flow etc. then the paper introduces the distributed object technique with the focus on the description of corba and the specific developing tools visibroker. finally, a multi - client distributed monitoring system based on corba is developed with multi - technologies referred before

    本文首先系統地介紹了bp神經網路、核函數概率估計（ kde ） 、遺傳演算法（ ga ）和帶外生變量的自回歸模型（ arx ）發展和研究概況以及上述建模演算法在分散式監測系統中的應用，並給出了運用石油流化催化裂化模擬設備的數據測試結果。
  11. Based on the combination of evolution strategy and limit equilibrium method, an effective global optimization method is proposed to allocate the most dangerous non - circular critical slip surface corresponding to the minimum factor of safety in slopes

    摘要將進化策略與邊坡穩定極限平衡法相結合，建立了邊坡任意形狀最危險滑裂面及相應最小安全系數的全局優化搜索方法。
  12. We discussed the main characteristic parameters of seismic kinesiology and dynamics of mine engineering fracture zone, including relative amplitude, phase time of wave crest, similarity factor, principal frequency band energy, 3 - d space time gradient and coherent coefficient et al., and puts forward the processing method of 3 - d seismic characteristic parameters about denoise - smoothing, generalization, correlation analysis, characteristic transformation ; and presents the method of pattern recognition of mine engineering fracture zone

    摘要本文從時間域、頻率域、三維空間域介紹了礦山工程裂隙破碎帶主要的地震運動學、動力學屬性參數，包括相對振幅、波峰相位時間、相似系數、主頻帶能量、二維空間時間梯度和相干系數等，提出了礦山工程裂隙破碎帶三維地震屬性的去噪平滑、歸一化、相關分析、特徵變換的處理方法以及裂隙破碎帶的模式識別原理與方法，並用實例說明了該方法的應用效果。
  13. The concrete used in testing bridge is monitored and some performance at definite age including compressive strength, splitting fensile strength, frost resistance, scaling frost resistance, chloride ion diffusion coefficient ( dcl - ), resistance of carbonization and pore structure by mercury porosimetry are tested. these performances are compared with that of concrete which designed by traditional method. the results show that mechanical properties of concrete designed by high durability concrete proportion and traditional method meet require ment at any age, however, frost resistance, scaling frost resistance, chloride ion diffusion coefficient ( dcl - ), resistance of carbonization and pore structure of the former are better than the latter, so high durability concrete is economic benefit

    對試驗橋用混凝土的質量進行監控，並成型試件測量所需齡期內的抗壓強度、劈裂強度與抗凍融、抗鹽凍、氯離子擴散系數（ dcl - ） 、抗碳化等耐久性能指標及孔結構，並與傳統混凝土進行對比研究，結果表明:高耐久性混凝土及按傳統配合比設計的混凝土的力學性能均能滿足相應齡期的要求，但前者的抗凍融性能、抗鹽凍性能、抗碳化性能、 dcl -和孔結構明顯優於後者，並具有明顯的社會經濟效益。
  14. In the light of its special property being not easy to gain strength, through mechanics researches on different methods to stabilize this kind of low _ liquid _ limit silty soil as subbase material, evaluated both technically and economically, we have got a cement lime stabilization plan to meet the index requirements for non _ side _ limit strength of compression of subbase of class2 road stipulated in the specification ; by means of improving the workmanship, thickening the loose layer of soil, adding soil on covering weave fabric before compaction, such problems can be solved as very poor compaction, loose surface during compaction, roughness and unevenness, coats of layer and shear damages

    本文針對黃河沖積而成的低液限粉土其粘粒含量極低、土的不均勻系數很小、膠體活性差的工程特性，通過採用不同方法穩定該類土作底基層材料的力學性能研究，從技術、經濟角度綜合評價，得到滿足規范抗壓強度指標要求的水泥石灰穩定方案。通過對原材料、試驗配合比設計、施工、等方面進行優化，從而顯著減輕了基層的早期及長期縮裂程度，從而提高了路面的耐久性。
  15. Thereafter, the fractal dimension value of cracks distribution was presented as an effective index to appraise the corrosion level. relations between fractal dimension and rebar corrosion ratio, concrete deterioration factor and strength of the member were studied respectively. fractal nn model was also built up to predict the ultimate load bearing capacity of crc members obtained from the field corroded structures, good results are achieved, which could provide an applicable method to evaluate the durability of crc members

    揭示出受腐蝕鋼筋混凝土構件在荷載作用下表面裂縫分佈服從統計意義上的分形，並對其進行了分形描述；提出以裂縫分形維數作為受腐蝕程度的有效衡量指標，首次實現了構件受腐蝕程度的定量描述；建立了裂縫分形維數與鋼筋銹蝕率、混凝土劣化系數、構件承載力之間的定量關系，並建立了分形神經網路模型對實際受腐蝕鋼筋混凝土構件進行了極限承載力的預測，取得了較好的預測效果。
  16. Observing the total error curve, the convergent speed is faster, and the error precision is higher then a group untrained experimental data are input the simulative system in turn. and their predicting results are satisfying

    根據小型催化裂化裝置進行重油催化裂化反應試驗的試驗數據對系統進行預測能力分析，從全局誤差曲線圖可見訓練速度比較快，誤差精度比較高。
  17. Abstract : a series of techniques producing lube base oil developed by ripp, including the technique for production of naphthenic lube oil, high viscosity base oil from sour crude and the api group base oil with viscosity index more than 120 from hydrocracking tail oil, were introduced

    文摘:介紹了石油化工科學研究院開發的一系列潤滑油基礎油生產技術，主要有環烷基潤滑油生產的工藝技術，含硫原油生產高粘度指數基礎油的技術以及加氫裂化尾油制取粘度指數大於120的類基礎油技術。
  18. In the laboratory experiment part, human peripheral blood, cultured cells and icr mice were study objects. the changes of mitotic chromosome numbers were measured by human metaphase chromosome counts and statistic analyzed used x2 - test. the changes of meiotic chromosome numbers were measured by mice one - cell zygote chromosome counts and statistic analyzed usedx2 - test. the effects of low dose ionizing radiation on the expression of topoisomerase ii were measured by immunocytochemistry, western blot and rt - pcr

    流行病學結果顯示長期小劑量輻射接觸與染色體不分離呈正相關，為進一步在細胞遺傳學和分子生物學方面研究小劑量電離輻射與染色體不分離關系及其機制，本課題第二部分以外周血、培養細胞、 icr小鼠為研究對象，用外周血染色體計數和單細胞受精卵染色體計數的方法研究小劑量輻射和拓撲異構酶復旦大學2000級博士生學位論文11a抑制劑及其二者的協同效應對有絲分裂和減數分裂染色體不分離的影響，用免疫細胞化學染色、 westernblot 、 rt pcr等方法研究了電離輻射引起拓撲異構酶a表達變化。
  19. In the existing literature, the material coefficients are simply considered as constants. yet the material coefficients c and n in paris formula are randomized in this study. using the least square method, the statistical correlation between c and n is obtained through the numerical value collocation

    將以往文獻中通常看作是確定性的材料系數隨機化，通過對大量數據進行數理統計的分析，將疲勞裂紋擴展速率paris公式中材料系數c和n視為隨機變量，採用最小二乘法對c和n進行數值擬合，從而得到二者的統計相關性表達式。
  20. There are three difficulties and key problems in this papaer : : the first problem is what is the dominance bearing of the leakage fractures, and how the bedrock fracture water distribute, the second is how to test the complex chemical behavior in experiment way and quantify the relative parameters, the last question is how to number the transportation of the element 90sr and its pollution to solve the three problems, this paper does lots of work and come to the prospective order, the creativities in this thesis as follow : ( 1 ) the dominance bearing of the leakage fractures and the distribution feature of the fracture water are ascertained based on rich geological data, these basal researches are very important, which are the premises to build the transport model of the fracture water in hae field

    本項研究工作的難點和關鍵問題有三個： hae處置場基巖裂隙系統中，導水裂隙的優勢方位是什麼，基巖裂隙水活躍帶分佈情況如何；怎麼對核素遷移的復雜化學行為進行實驗室測試並取得有關定量化參數；怎樣數值化表現出溶質的遷移行為和污染情況本論文在解決以上三個問題上做了大量的工作，達到了預期的目的，其創新之處有以下三點： （ 1 ）通過地質資料的分析，首次提出了hae預選處置場基巖裂隙導水的優勢方位和基巖裂隙水活躍帶的大致分佈特徵。它是一個很重要的基礎性研究成果，是建立hae處置場水運動模型的前提。
分享友人
分享到 Line

分享到臉書