補償前饋 的英文怎麼說

中文拼音 [bǔchángqiánkuì]
補償前饋 英文
compensating feedforward
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 前 : Ⅰ名詞1 （在正面的） front 2 （次序在先的） first; top 3 （過去的; 較早的） ago; before; preceding...
  • 饋 : 動詞（饋贈） make a present of
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. On the basis of the situation analysis for practical engineering application, it is put forward to add compensating measures in airspace circuit including instruction feedforward, target feedforward, carrier aircraft feedforward and radome refraction compensation to improve the airspace stabilization accuracy

    根據實際工程應用中的情況分析，為提高空域穩定精度，提出了在空域穩定迴路中加入補償措施，即指令前饋、目標前饋、載機前饋和天線罩折射補償。
  2. The other is an improved fuzzy neural network that is joined a compensative operation layer and adopts the improved center - or - gravity defuzzication in feedforward fuzzy neural network based on gaussian fuzzy logical system

    其二是改進的補償模糊神經網路。該網路在基於高斯模糊邏輯系統的前饋模糊神經網路中加入了補償運算層和採用了改進型中心反模糊化器。
  3. Finally, the friction model is applied after analyzing the mechanical structure of tracking system. the friction compensation had been obtained by differential feedforward applied to the output of position controller

    最後建立了低速跟蹤情況下的摩擦模型，並用微分前饋的方法實現摩擦補償，消除摩擦對跟蹤精度的影響，提高了跟蹤精度。
  4. As for single axis, pewin, the software given by the programmable multi - axis controller ( pmac ), is used to find the best parameters of the pid controller and feedforward compensation controller. then, the nonlinear friction in the system is compensated by the friction compensation controller with genetic algorithm ( ga ). the compensation controller can improve the system performance effectively

    對于單軸系統首先利用美國deltatau公司的可編程多軸控制器pmac自帶的控制軟體pewin進行pid參數的整定以及前饋補償環節的參數整定，然後分析系統存在的非線性摩擦力，利用遺傳演算法尋優摩擦力補償環節的參數，達到補償摩擦力的效果，有效地提高了系統的控制性能。
  5. Control effect with high accuracy and stability on hydraulic shovel is achieved by feedback plus feedforward, nonlinear compensation, state feedback and gain scheduling on conditions

    通過採用反饋加前饋控制、非線性補償、狀態反饋和根據狀態對增益編排，獲得了對液壓正鏟挖掘機的高精度控制效果和高穩定性。
  6. Research on ultra - precision machine tools ' servo control technique based on disturbance feedforward compensation

    基於擾動前饋補償的超精密機床伺服控制技術研究
  7. In order to improve dynamic performance of the control system in the assembly robot, according to acpmsm ( ac permanent magnet synchronous motor ) vector control model and the control idea about preview control, the paper presents a kind of control strategies that is composite of a primary pid ( proportion integral dif - ferenfial ) with a preview feed - forward compensation, its compensation is equivalent to linear combination of future adjacent difference, the simulation results show that it can not only improve the system tracking performance effectively, but also implement easily

    摘要為了提高裝配機器人控制系統的動態性能，依據交流永磁同步電機矢量控制模型，從預見控制的思想出發，提出了一種在原有pid基礎上外加預見前饋補償的控制方法，這種控制方法的前饋補償項取未來幾項目標值一階差值的線形組合，並模擬驗證了該控制方法對提高系統跟蹤性能的有效性和簡單可行性。
  8. Based on x - filtered lms algorithm and - filtered lms algorithm adaptive inverse control, we use a new variable step size lms algorithm. adding little computation, variable step size lms algorithm can result in fast convergence speed and low residual error simultaneously. the adaptive feedback control can counteract the beginning error of the system

    在原來的x -濾波lms演算法自適應逆控制和-濾波lms演算法自適應逆控制方法的基礎上，引入了新的變步長lms演算法，在計算量增加不多的前提下，能同時獲得較快的收斂速度和較小的穩態誤差；引入自適應的反饋補償控制克服了被控系統的直流零頻漂移，使控制系統在初開始工作階段快速收斂；還引入自適應擾動消除器，它能最大限度的消除擾動。
  9. A design strategy based on state feedback and feedforward compensator for helicopter flight control system

    基於狀態反饋及前置補償策略的直升機飛控系統設計
  10. After analyzing compensation conditions for 3 - axis stabilization to overcome disturbance from ship surge, sway and yaw, two control strategies - feed - forward compensation and closed - loop feedback compensation - are given. these two strategies are applied to antenna stabilized tracking system with good performance. intelligent pid is used in closed - loop feedback compensation to get high tracking precision and rapid response

    重點分析了天線穩定控制系統的三軸補償條件，提出了穩定系統抑止載體擾動的控制策略：對于橫滾和俯仰系統採用前饋補償的控制策略；對于方位系統，在以步進電機為驅動元件的特定條件下，研究了變控制周期的閉環反饋策略，同時成功將智能pid演算法應用於實際系統，提高了系統的跟蹤精度和響應快速性。
  11. Presents a simple method of compensating friction against the character of the nonlinear model of a brushless dc motor system which transfers the original system model to a simple linear model using the method of input - output linearization, and estimates the coulomb friction in the system in real - time using a nonlinear friction estimator, and then compensate the friction in the system using a friction feedforward, and concludes from simulation results that this method can effectively eliminate the influence of friction in brushless dc motor systems

    針對無刷直流電動機系統的非線性數學模型特點，提出了一種簡單的摩擦補償方法.該方法首先利用輸入輸出線性化方法將原系統模型轉化為一種簡單的線性模型，然後給出一種非線性摩擦估計器實時估計系統中的庫侖摩擦值，最後利用摩擦前饋補償方法對其進行補償.模擬結果表明該方法可以有效地抑制無刷直流電動機系統中的摩擦影響
  12. By solving iterative the sequences, the optimal control law is obtained which consists of analytical linear feed - forward - feedback terms and a nonlinear compensation term, which is the limit of the adjoint vector sequence

    通過迭代序列得到的最優撫動抑制控制律由解析的線性前饋反饋項和序列極限形式的非線性補償項組成。
  13. In this thesis, the decoupling unit of vav system is designed in the way of feedforward conpensation. then the transfer function matrix of the feedforward conpensation decoupling unit of the 5 inputs & 5 outputs vav system is worked out. the decoupling conpensation unit can change the transfer function matrix of the open loop and closed loop control system into diagonal matrix, so that the coupling among the five control loops is eliminated, and vav system is decoupled

    本文採用前饋補償法設計了變風量空調系統的解耦補償器，並得出了五輸入、五輸出變風量空調系統前饋補償解耦器的傳遞函數矩陣，該解耦補償器可以使本文所研究的變風量空調控制系統的開環傳遞函數矩陣和閉環傳遞函數矩陣都變換為對角矩陣，從而解除五個控制迴路之間的耦合，使變風量空調系統實現解耦。
  14. Two schemes to realize the new detection approach and according apf are accomplished and verified. ( 1 ) the lcc detection method using a feed - forward multilayer ann to realize the adjustment of lcc

    提出並完成了兩種不同的實現方案： （ 1 ）前饋多層ann實現補償電流有效值最小的調節方案和相應的apf電路。
  15. Based on the research of siso case, we employ the method of feedforward compensation to decouple multiple input and multiple output ( mimo ) plant. it is the key point to design h2 - optimization compensator with the approach of l2 - norm optimization so as to apply directly the result of siso case to the decoupled system

    在對單輸入單輸出的對象研究基礎之上，作者採用相對增益法和前饋補償方法對多輸入多輸出（ mimo ）的對象進行前饋補償解耦，在這一過程中關鍵就是引入頻域l _ 2范數優化的方法對補償器進行設計使之具有h _ 2優化的特點。
  16. The orpadtc model can always match the real process and the upldt output, which can be used as the feed back signal of the control system, can be predicted. the orpadtc completely solves the problems, sensitive to the error of the model parameters and the low power against disturbance, which exist in the traditional smith c ompensator

    這樣無論實際受控過程的參數怎樣變化，只要不影響系統的穩定性，對象參考參數自適應時滯補償器的模型總能和實際過程趨於一致，並提前獲得大時滯不確定過程實際輸出的預測值，以便在構成閉環控制系統時替代實際輸出作為反饋信號。
  17. This article emphatically discussed and analyzed following points : load command feed forward function can improve the rapid respond character of steam turbine generator ; lead of load command have advance control function on boiler main control and can highly improve the stability of main steam pressure ; the use of predict control and state space variable function can improve the quality of boiler steam temperature control effectively, control the steam temperature in the defined range and increase the boiler and turbine life and efficiency even if working state changed in a big range ; linear compensation can restrain the vibration of generator load in the condition of big loa d change

    本文重點討論、分析提出負荷指令前饋作用可以提高汽輪發電機快速響應特性；負荷指令的導前功能對鍋爐主控有超前控製作用，能顯著提高主蒸汽壓力的穩定性；採用預測及狀態空間法能有效改進鍋爐蒸汽溫度控製品質，在大幅度工況變化下仍有效控制蒸汽溫度在額定范圍內，提高鍋爐、汽輪機壽命及其效率；汽輪發電機組的快速響應性與汽輪發電機組負荷振蕩問題間的平衡關系，採用線性補償可以有效抑制在負荷變化梯度較大情況下發電機負荷振蕩問題。
  18. This paper introduces the principle of real - time automatic gain control based on feed forwarding technology, and the realization of the critical technologies including digital compensation and synchronization, as well as, the specific application of communication analyzing instrument

    摘要闡述了基於前饋技術的實時自動增益控制的原理及同步和數字補償等關鍵技術的實現；介紹了在通信分析儀中的具體應用。
  19. Feed back control base on nonlinear pid with self - adjust parameter and feed forward control base on experience model are employed in the practical application. the realization of this control system and its result are introduced in this paper. because the process of the reaction is complicated, it ' s difficult to model for it

    在對中和過程自動控制演算法的探索中，採用了非線性參數自整定控制和基於模型的前饋控制，本文介紹了這種控制系統的實現和現場控制效果，由於中和控制過程的模型極其難以確定，反應過程變化復雜，因此基於模型的前饋控制無法對ph值和流量值的波動進行有效的補償。
  20. The satellite attitude backstepping controller is designed. in order to compensate the disturbance of infrared camera, a compounding feedforward controller is proposed basing the momentum conservation

    基於動量守恆定理，設計了用於補償紅外相機干擾作用的前饋控制器，從而提出預警衛星姿態的反饋-前饋復合控制方法。
分享友人
分享到 Line

分享到臉書