裝入控製程序 的英文怎麼說

中文拼音 [zhuāngrùkòngzhìchéngxù]
裝入控製程序 英文
loading control program
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 入 : Ⅰ動詞1 （進來或進去） enter 2 （參加） join; be admitted into; become a member of 3 （合乎） conf...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 裝入 : place; load; embed
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. First, according to different car - following situation, warning distance model and braking distance model are discussed detailed. then according to base function to be achieved, system plan is made, and based on this, design of applying circuit of needed power unit, information collection unit, warning unit and other units is finished. system control program is designed by mcs - 51 language

    根據不同的跟車情況對報警距離模型和制動距離模型進行了深入的探討；然後根據所要實現的基本功能，建立了系統方案，並以此為基礎，進行系統所需的電源、信息採集、警報輸出及其它裝置的應用電路設計；用mcs - 51匯編語言編制了系統控製程序；最後給出了模擬實驗的結果。
  2. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  3. This is a big complicated monitoring and control system, the article only discusses a part of the units, includes : the components of neutral beam injection and the requirements for monitoring and control system, the argumentation and selection of control scheme, the research of data acquisition system based on pci bus, the design and realization of hardware and software of dac, the means of concentrated data storage and management, the communication program design of subsystem under different mode and protocol. the last part gives some experiment system running data

    這是一個大型復雜的監控系統，本文只就其中的幾個單元的設計與實現展開討論，主要內容包括：中性束注入裝置的組成及其對監控系統的要求，監控系統控制方案的論證和選擇，基於pci總線的小型數據採集系統的研製，多功能數據採集卡的硬體和軟體的設計與實現，集中式數據存儲與管理的方法及其實現，多功能子系統之間在不同通信方式、不同傳輸協議下的通信實現及其程序設計。
  4. So the research presented here is concentrating on digitization welding inverter used for co2 welding, aiming at improving the performance of welding power source. in this paper, we develop a waveform control system using tms320f2812 dsp and at89s8252 and establish a sample inverter on the basis of the dsp technology and the embedded system application. besides, the power system has the function of carbon dioxide gas shielded welding using double - slope waveform control method

    本文結合當前dsp技術和嵌入式系統發展的最新成果，選用tms320f2812dsp和at89s8252單片機設計了co2焊逆變電源控制系統，組裝、調試了一臺逆變電源樣機，並通過編寫控製程序初步實現了基於短路電流雙斜率上升波形控制的co2焊的功能。
分享友人
分享到 Line

分享到臉書