裝配簡圖 的英文怎麼說

中文拼音 [zhuāngpèijiǎntú]
裝配簡圖 英文
assemble schematic
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 簡 : Ⅰ形容詞（簡單） simple; simplified; brief Ⅱ動詞1 （使簡單; 簡化） simplify 2 [書面語] （選擇人才...
  • 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
  • 裝配 : assemble; fit together; fit out; assembling; fitting; rigging; erecting; fabrication
  • 簡圖 : abbreviated drawing; diagram; diagrammatic sketch; sketch; sketch drawing; schematic diagram; blo...
  1. Abstract : a new waveguide which can change the wide wall of a rectangular waveguide into a symmetric arc wall is named as a cam - rectangular waveguide. comparing to sectoral waveguide, the new waveguide has the same voltage characteristics and is easier to be produced and fixed. an approximate formula of the dominant mode fields and the normalized conductance of a longitudinal resonant slot cut in the curved wall of a cam - rectangular waveguide are given. a resonant slot linear array in c & x band is designed, in which the slot voltage distribution is equiphase and the input is matched. the input voltage stationary ware ratio and the h - plane pattern of the antenna are measured. the experimental results show the conformance with theoretical results

    文摘:把常用的矩形波導一個寬面改成圓弧形構成的波導稱為圓突-矩形波導.這種波導與扇面波導相比：電性能相當；波導管結構更加簡單，容易加工，便於安裝.文中給出圓突-矩形波導中主模場，圓曲面上縱向槽歸一化諧振電導近似公式.設計了c和x波段波導曲面縱向諧振縫隙線陣，縫隙電壓相位為同相分佈，輸入端匹配.實際測量了天線輸入端電壓駐波比和h面方向圖，理論與實驗相吻合
  2. First, the paper summarizes a group building csg entity and makes combination mode of csg entities clear, by abstracting building model and analyzing building graphic objects. depending on this model, the article describes topology relations of the 3d architecture model inner based on the point, line, surface and entity. finally, in the developing environment vc + +, based on the opengl techniques, 3d building model of tyut office building is implemented by csg

    首先，通過對建築模型抽取和建築圖形對象的分析，總結了一組描述建築模型的建築csg體元，揭示了建築模型csg體元之間的組合形態，提出一種基於csg的組合建模方案來構造三維建築模型；然後在此模型基礎上進行了基於點、線、面、體的表達方式描述了建築模型內部拓撲空間關系，簡要介紹了建築模型的體裝配方法；最後利用opengl技術在visualc + +下實現了工大辦公樓的csg建模實驗。
  3. On the base of deducing meshing theory, by simplifying the parameters and using software, the 3d model of the rolling cone - type toroidal drive is given. and the parametric models are realized. the assemble chart of drive is given

    在嚙合理論推導的基礎上，通過對滾錐齒超環面行星蝸桿傳動的各參數進行簡化處理，利用計算機軟體對滾錐齒超環面行星蝸桿傳動進行了三維實體參數化建模，實現了模型的參數化，給出了該傳動的裝配圖，並進行了動態模擬。
  4. Defining the pose parameters of the tool as the driving dimensions and the length of actuating limbs as the driven dimensions, the configuration of the simulation mechanism was varied correspondingly with the variation of the driving dimensions and the driven dimensions ( length of actuating limbs ) could be acquired and recorded

    給出了並聯機床機構簡圖和虛擬樣機實體模型，通過將數控代碼進行預處理，進行了並聯機床的虛實映射計算，即給定刀具位置和姿態的驅動尺寸、驅動桿件長度的被驅動尺寸，在裝配約束作用下驅動尺寸帶動整個機構運動，記錄桿件長度的被驅動尺寸，求解出桿長的值。
  5. Based on the research and analysis of information of assembly of product, semantic of assembly is divided into four types in order that assembly mode is expressed briefly and definitely. assembly mode of product is described through graph of assembly semantic by the way of the theory of graph

    在產品裝配關系深入研究和分析的基礎上，為使產品裝配模型信息表達簡潔、意義明確，將裝配關系分成4種基本類別，採用圖論方法對產品的裝配模型進行圖的表達。
  6. This article gives you an overview of the steps to prepare to install and configure the lcd the image screen, the modeline a configuration line that tells the server how to drive the monitor, and the touchscreen for input

    本文將簡要介紹如何準備安裝並配置lcd （圖像屏幕） 、 modeline （一個配置行，告訴服務器如何驅動監視器） 、觸摸屏（用作輸入） 。
分享友人
分享到 Line

分享到臉書