觸輪桿 的英文怎麼說
中文拼音 [chùlúngǎn]
觸輪桿
英文
trolley pole-
The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters ， the cad system can make optimization design and strength check for the worm gear ， draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm ， judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point ， make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統：包括幾何參數設計計算模塊，強度校核模塊，繪制齒面接觸線模塊，蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊；開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫，建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫；開發了平面二次包絡環面蝸桿減速器參數化建模軟體：包括零部件的參數化建模模塊和裝配圖的參數化建模模塊，其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3
通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3However, the accuracy and instantaneity of the most used mark post measurement method are not good and the errors of five - wheel measure device with contacting measurement principle are serious when it is used in soft and undulated surface field
但是，常用的標桿法測量精度和瞬態性較差，接觸式測量的五輪儀法用於田間松軟、不平的地況誤差較大。Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive
本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2It can be regard as the theoretical basis to optimize the drive. according to the gear meshing theory, the meshing equations, the contact line equations and tooth profile equations are given. it gives a base for 3d modeling the drive
按照齒輪嚙合理論，推導出了滾錐齒超環面行星蝸桿傳動的接觸線方程、嚙合方程及各輪輪齒的齒面方程，為滾錐齒超環面行星蝸桿傳動的三維建模奠定了基礎。After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller
對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。Contact force between chain - and sprocket, blade, guide
-鏈條與鏈輪張緊器臂導向桿間的觸點壓力Abstract : calculation of the length of contact lines of a double enveloping wormgearing with planar generating surface and finding out the size of contact area are th e foundation of strength analyses of wormgearing
文摘:計算平面二次包絡環面蝸桿副的接觸線長度和了解蝸輪齒面接觸區域的大小是蝸桿傳動強度分析的基礎。The pot consists of pot body, brace, worm and worm wheel. the pot body can rotate within 180 degree. the equipment adopts open - top concentration, which is mainly used to boil and concentrate liquid materials of pharmacy, food, chemical engineering and light industry. the part contacting materials adopts stainless steel sus304, this equipment is anti - corrosion and durable, it is in accordance with gmpmedical system. mixing device can be added at users ; request
可傾式夾層鍋由鍋體、支架、蝸輪、蝸桿等部件組成，鍋體可作180度以內的轉動，本設備為敞口式濃縮，主要用於制藥、食品、化工、輕工等行業對料液的煎煮和濃縮，該設備與物料接觸部分為不銹鋼sus304 ，具有較好的耐腐蝕性能，經久耐用，符合gmp醫藥標準，同時亦可根據用戶要求，可增加攪拌裝置。分享友人