計數損失誤差 的英文怎麼說
中文拼音 [jìshǔsǔnshīwùchā]
計數損失誤差
英文
counting-loss error- 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
- 數 : 數副詞（屢次） frequently; repeatedly
- 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
- 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
- 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
- 計數 : count; tally; counting計數卡 numbered card
- 損失 : 1. （失去） lose 2. （失去的東西） loss; wastage
- 誤差 : error
-
( 5 ) it was more precise for using darcy - weisbach formula to calculate the hydraulic pressure slope curve in the lateral line, but too complexity. although i - pm wu formula is simple, the estimated results were not agreement with the measured data. a coefficient including irrigation uniformity was presented to modify i - pal wu formula, and the results were agreement after using the coefficient
（ 4 ）利用達西?韋斯巴赫公式計算微孔毛管的沿程水頭損失具有較高的精度，但計算復雜，吳義伯公式計算雖較簡單，但在灌水均勻度較差時誤差較大，為此對吳義伯公式進行了修正，提出了修正系數的計算經驗公式，取得了良好的結果，為簡易地下滴灌工程設計中水力計算建立了簡化公式。At the same time, the method of disposal phase shift of ct by compensation is introduced. then the analysis and statistic of electrical power quality, the control scheme and compensating amount of capacitor for reactive power compensation are analyzed respectively. and in the paper, the control with a / y and the switch with ac contactor and solid state switch is valid measure not only for improving operate level economically and amending electrical power quality but also for avoiding of replacing switch frequently and decrease economic loss
然後對現有的演算法進行了詳細的分析、比較，篩選出既能滿足硬體要求又可降低投資、保證精度、簡化軟體的方案，確定了準同步采樣的方案，並通過對準同步采樣誤差的分析，提出了一種從45開始采樣，從而提高精度的采樣數據處理辦法，同時，對于電流互感器相位漂移提出了一種補償辦法，接著對裝置中電能質量分析與統計以及無功補償中電容器的補償量、投切原則也作了相應分析，其中對于無功補償採用y混合接線，並利用交流接觸器和固態開關共同投切電容，不但提高了經濟運行水平、改善了電能質量，而且有效的避免了頻繁更換開關，減少了經濟損失；最後，設計了裝置的硬體電路並繪制了相應的軟體流程圖。At last the toleramce design has been fulfilled with the method of inner and outer design integral analyse, the effect of the clear factors on the characteristic and stability of the product has been studied, through which the qulity losing function has been established, and the toleramce of the clear factors have been made sure
最後進行了產品的容差設計。通過內、外設計的直積分析方法，分析了顯著因素的誤差對產品性能及穩定性的影響，建立了質量損失函數和確定了顯著因素的容差。
分享友人