設計計算模型 的英文怎麼說

中文拼音 [shèjìjìsuànmóxíng]
設計計算模型 英文
design calculation model
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  • 計算 : 1 （求得未知數） count; compute; calculate; reckon; enumerate 2 （考慮; 籌劃） consideration; pla...
  • 模型 : 1 （仿製實物） model; pattern 2 （制砂型的工具） mould; pattern3 （模子） model set; mould patter...
  1. The pressure drop of the compound tray can be regarded as consisting of dry plate pressure drop, clear liquid resistance, liquid surface tension resistance, and packing pressure drop. the model that has established can fairly predict the pressure drop of the compound tray, the value calculated by the model compared with that detected by experiment is less than 20 %

    復合塔板的壓降可認為由干板壓降、清液層阻力、填料層壓降和克服液體表面張力的壓降四部分組成，所建立的壓降計算模型，能較好地預測復合塔板的壓降，計算值與實驗值誤差在20以內，可用於工程設計。
  2. It can be used not only to change the fire precision of the base bleed projectile, but also to improve the effect of reduction drag and expansion range. the calculating model of the secondary expansive pressure of the burning gas is constructed by means of analysis of the experimental resuits, it has been confirmed that the new base bleed unit can be designed, with the secondary expansive principle of the burning gas pressure. the engineering project of a hybrid base - bleed - rocket high - level efficient extended - range projectile is designed, with the secondary expansive principle of the burning gas pressure, the feasibility and the true worth of its engineering applications is validated in theory

    本文提出了底排燃氣壓力不隨外部壓力變化，既可改善底部彈射擊精度又可提高減阻效果的二次擴張原理，建立了底排燃氣二次擴張壓力的計算模型，並通過採用二次擴張原理的新型底排裝置與傳統底排裝置的對比試驗，驗證了新型底排裝置結構實現的可行性；完成了基於底排燃氣二次擴張高效增程原理的底排?火箭復合高效增程彈方案設計及其有關計算，從理論上驗證了其工程應用的可行性和實際價值。
  3. This paper focuses on the research of the stress mechanism of the ribbed shell structure in statics, dynamics and under the explosive load on the basis of the engineering practice of cave depot of single aircraft. in this paper, according to the classical shell theories, the basic differential equilibrium of the ribbed shell structure and the finite element analysis of 3d rippled plate are established, in which the function of annular ribs reinforcement bars and 3d ripped steel plates are distributed in the range of the steel, and the functions along the longitude direction of tension, bending, and torsion are neglected ; applied with dynamic analytical theory, the dynamic model of ribbed shell structure and the analytical theory model of elastic - plastic are set up ; the triangle series method is used to solve the displacement and stress under the distributed load and the concentrated load of the ribbed shell structure

    本文以軍用機場地面單機掩蔽庫工程建設為工程背景，首次對內襯三維波紋鋼板混凝土拱型復合結構的受力機理進行了靜力、動力和爆炸荷載的分析研究。根據將橫肋、鋼筋及三維波紋鋼板的作用均勻分佈在殼體范圍內的情況，忽略橫肋、鋼筋及三維波紋鋼板沿殼體母線方向的抗拉、抗彎及其抗扭作用，首次推導出了內襯三維波紋鋼板混凝土殼體的微分平衡方程，建立了有限元計算模型，並採用三角函數法，求解了三維波紋鋼板混凝土拱型復合結構在分佈荷載和集中荷載作用下的位移響應和應力響應，並與普通殼體進行了比較。
  4. According to the measuremental data of the two ammunications, the anti - designed computation and analysis of aerodynamic characteristic, flight stability, exterior ballistic characteristic for the two ammunications are studied with the advanced methods of the exterior ballistics. using the monte calo algorithm, the statistic mathematical model about ammunication ' s intensity is established and the 1000 miter vertical target intensity and the fall intensity are discussed in detail for the two ammunications. the improval potential and the main technical approachs of these ammunication ' s exterior ballistic performances are presented by compositive optimal algorithm

    根據工廠對俄ak130艦炮彈藥的測繪數據，利用先進的外彈道數值分析方法對兩種彈藥的空氣動力特性、飛行穩定性特性、外彈道特徵量等進行了反設計計算分析；採用montecarlo方法，建立了艦炮彈藥密集度性能統計分析數學模型，對兩種彈藥的立靶密集度和地面密集度進行了詳細的計算分析；利用外彈道性能綜合優化設計方法對兩種彈藥的外彈道性能指標的改進潛力和主要技術途徑進行了分析。
  5. In accordance with a boiler whose capacity is 1025t / h in a certain power plant ， this paper builds the heating calculation model of new method and the former soviet union method, finds the solutions to the model under the designed coal quality, compares the results with the design data, verifies and analyzes the new heating calculation model

    針對某電廠1025鍋爐機組，按照新方法和前蘇聯方法分別建立熱力計算模型，在設計煤質下對模型進行求解，將計算結果與設計數據進行比較，對新方法進行驗證和分析。
  6. The design tools of isight such as integration, design of experiment, approximation and optimization are applied to develop the design and optimization software for airfoils of wing - in - ground air vehicle

    本文應用多學科優化軟體isight的過程集成、試驗設計、近似模型、優化演算法等功能開發了地效飛行器翼型優化設計軟體。
  7. In common design, the calculation of suspender inner force uses the model of beam with simply supported ends, because of all kinds of restraint

    由於各種條件的限制，在通常的設計計算中，利用橋面簡支梁模型計算吊索（桿）內力。
  8. The second problem is that after material choice, how can we put the material in proper position to avoid mouthpiece vertically. the third problem is that for every belt of the equipment " s material, what angle can we put the joint weld, because the improperly arrangement of joint weld will reduce the equipment ' s pressure _ bearing ability. the thesis has researched the optimizing condition of material selection and weld joint position arrangement in chemical equipment making technology. the author also discuss the optimized model and develop a stock layout software by using microsoft corporation ' s tools visual basic 6. 0

    本文針對以上問題，根據化工設備生產實踐討論了化工設備製造過程中對材料用料選擇的優化及排料時焊縫位置（環縫、縱縫）的優化，建立了用料選擇優化計算模型及焊縫位置的優化計算模型，並利用microsoft公司的程序開發工具visualbasic6 . 0開發了化工設備智能排樣系統，該系統可以根據用戶材料及用戶在設備製造過程中各種要求進行優化計算並輸出優質的設備製造排樣圖。
  9. The optimization objective is to minimize the entire system ' s line loss per day, and the permissible number of equipment switching is considered as the constraint in this model

    針對計算模型，基於遺傳演算法的思想，設計了相應的編碼、雜交和變異操作。
  10. This paper deals with seismic response of a tunnel - soil system immersed tunnel ， as an underground structure ， must be compatible with the deformation of the surrounding soil thus the simplified model for a tunnel - soil system is established through two steps at the first step ， an mdof system is developed for modeling the foundation soil to this end ， dynamic behavior of the foundation soil is analyzed a typical section of the foundation soil simplified as a single mass - spring system on the basis of some equivalent criteria those mass are linked longitudinally by elastic springs to form an mdof system at the second step ， the tunnel is treated as a beam on elastic foundation ; that is ， the tunnel is connected with the soil massed to form a tunnel - soil system this model has been applied to the seismic analysis of huangsha fangcun immersed tunnel across the pearl river in guangzhou design recommendation is proposed on the basis of this analysis

    研究沉管隧道在地震條件下整體受力的分析方法分兩步建立計算模型第一步通過分析場地地基土切片的動力特性，根據等效原則將其化為等效單質點體系，然後在縱向用等效彈簧連接而成為多質點體系的地基土計算模型；第二步將隧道看作彈性地基梁與上述多質點體系通過等效彈簧連結而得到土隧道體系的計算模型本文結合廣州黃沙芳村珠江水下隧道工程實例建立了具體的計算模型並對多種不同的約束條件，進行了縱向與橫向地震響應時程分析，為該隧道的抗震設計提供依據
  11. According to the stress calculation of bolts of all common kinds of dryers with this model, the design method of bolts is put forward

    由該計算模型計算獲得國內所有常用規格烘缸的螺栓力，據此提出螺栓設計計算的方法。
  12. Firstly, the system is divided into many modules according to different point of view ; secondly, to the hardware equipment - vidicon, lenses, revolver, shield and decode device, their principle of work has been explained ; thirdly, according to image identification experience and other indexes of the system, the focus of the lenses and relative aperture are calculated, and the type of the camera is confirmed, at the same time, the energy of infrared lamp is also computed in the thesis ; at the same time, synthesis control box is devised

    首先，按照角度的不同，將系統劃分成許多模塊。其次，對硬體設備? ?攝像機，鏡頭，雲臺，防護罩，解碼器等的工作原理進行了闡述，再次，以人的成像辨認的經驗判據為依據，結合系統的其它指標，設計計算出鏡頭的焦距f 、相對孔徑d ，同時確定攝像機的型號，並計算出紅外燈光源。最後，對綜合控制箱進行設計，指出了設計的意義，實現的功能，並附上了綜合控制箱的外形圖。
  13. The development of hev energies management system not only needs ecu technology, math ' s model, software technology etc, but also has much work to do on actuator of design and manufacturing

    開發混合動力電動汽車多能源控制系統不僅在ecu技術、硬體設計、數學模型、演算法和軟體技術方面要求很高，而且在執行部件的設計與製造等方面都是難度較大的工作。
  14. Besides experiments, the present domestic and abroad study on anti - slide pile is mainly analysis by traditional cantilever beam method, foundation coefficient method and elastic mechanic method. on the basis of previous studies, this paper carries out a research on relevant design and calculation theory about anti - slide piles, comprising the interaction between anti - slide piles and rock and soil of side slopes, the soil arching model of anti - slide piles and the internal stress calculation method of prestressed anchor cables

    目前國內外對抗滑樁的研究，除試驗研究外，主要採用傳統的懸臂梁法、地基系數法及彈性力學方法來進行分析。本文在前人的研究基礎上，通過對抗滑樁相關設計計算理論進行研究，包括抗滑樁與邊坡巖土體的相互作用，抗滑樁的土拱效應模型以及抗滑樁預應力錨索的內力計算方法進行分析。
  15. The article below deals with the mechanism research of this kind of machine, describing the structure and principle ; theoretically analyzing the data to derive formula ; tentatively proposing theory of radial flow between parallel plates for future design ; pores arrangement, i. e., longitudinal pores are equally spaced, horizontal pores bore size is preferred unequal and rows distance can be either equal or not but generally smaller than pores distance, and rows shall be odd numbers and are arranged symmetrical from the center row and bore size reduces gradually from the center row

    本文對氣墊機作了機理研究，描述了氣墊機的結構型式及工作原理，對氣墊機的主參數作了理論分析，根據平行平板間的徑向流動理論，建立了計算模型，導出了計算公式，可作為氣墊設計理論的依據；提出了氣孔布置的原則：縱向孔間距相等較好，橫向孔徑不等為佳，橫向孔排距可以相等，也可以不相等，但一般小於孔間距。氣孔排數應為奇數，由中心兩側呈對稱布置，孔徑由中心向兩旁逐漸減小。
  16. In this paper, a numerical simulation model to analyze the function and effect of the pumping irrigation in sediment deposition reduction of the irrigation canal system is proposed

    除了以往有效的措施外，本文在總結灌區渠道不同部位設置提水泵站設施作用與效果的同時，通過建立灌區渠道懸移質沖刷計算模型，對其減淤清淤的作用與效果進行了理論分析研究。
  17. Design and calculation model of structured packed columns

    規整填料塔的設計計算模型
  18. This paper presents a general model in order to solve the problems existing in the process of developing the design and calculation module of digital manual

    摘要針對數字化手冊開發過程中的設計計算模塊的問題，提出了解決此類問題一種通用的模型。
  19. This paper integrates theory with practice, follows the principles and methods of software engineering, setup the constitutes frame of nc machine servo feed cad system, and finishes the research and development of four modules of servo feed cad system, such as graphical user interface module, design and compute module, database management system and graphics system, by using object orient programming ( oop ) technology, borland c + + builder 5. 0 database engine ( bde ), parametric feature model technology and 3d solid modeling technology

    本文理論聯系實際，遵循軟體工程的原則和方法，創建了數控機床伺服進給cad系統的總體框架。它採用了面向對象編程（ oop ）技術、 borlandc + + builder5 . 0數據庫引擎（ bde ） 、參數化建模技術和三維實體造型技術，完成了伺服進給系統的四大部分功能：即圖形用戶界面模塊、設計計算模塊、數據庫管理系統模塊以及圖形系統模塊。
  20. This essay explains the application conditions of anti - sliding piles, its design and calculation mode. we also narrate other calculations of rigidity piles and elasticity piles. as to the ecologic protection technology, we discuss the control of surface water and under underground and the protective methods that directly planting in the slope or in the frame soil

    論文詳盡說明了抗滑樁的使用條件、設計、計算模型及剛性樁和彈性樁的計算模式，對邊坡地表水、地下水的治理及土質邊坡的直接植草、框架內植草護坡等生態防護技術進行了探討說明。
分享友人
分享到 Line

分享到臉書