設計計算 的英文怎麼說

中文拼音 [shèjìjìsuàn]
設計計算 英文
design calculation
  • 設 : Ⅰ動詞1 （設立; 布置） set up; establish; found 2 （籌劃） work out : 設計陷害 plot a frame up; fr...
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
  • 設計 : devise; project; plan; design; excogitation; layout; layout work; styling
  • 計算 : 1 （求得未知數） count; compute; calculate; reckon; enumerate 2 （考慮; 籌劃） consideration; pla...
  1. In the dissertation ' s chapter 3 to chapter 5, the mechanical and physical performances of the engineering plastics are analyzed, the failure mode and the designing computing methods of engineering plastics member suffering the static load, dynamic load, impact load, pulse load, are studied. by the practice application and ball firing experiment of the engineering plastics key piece in the weapons, the precious experiences, for engineering plastics application and confirmation of the material performances guideline in the weapons, are obtained

    論文的第三章至第五章，分析了工程塑料物理機械性能，研究了受靜載荷、動載荷、沖擊載荷及脈沖載荷下工程塑料構件的失效模式和設計計算方法，通過工程塑料在槍械關鍵受力結構件上的實際應用和實彈射擊試驗，取得了寶貴的經驗，為高性能工程塑料在槍械上的應用和材料性能指標的確定奠定了基礎。
  2. The theory and design calculation of the carrousel oxidation ditch

    氧化溝理論與設計計算
  3. Diathermancy analysis and design calculation on the heating exchange of floor heating in the vertical tube of air conditioner system

    空調系統中垂直埋管地熱換熱器傳熱性能分析及設計計算
  4. This software system is consisted of two major blocks : computing block and drawing block

    本系統的軟體開發共兩大部分：設計計算程序的開發和繪圖程序的開發。
  5. Study on uplift mechanism and calculation of dx pile

    樁抗拔承載機理及設計計算方法研究
  6. The study on the electromagnetic design of active magnetic bearing

    磁懸浮軸承的電磁設計計算研究
  7. Second, the paper in - depth discuss the reinforce foundation operation mechanism of technique of composite grouting, including spray incise action of high pressure spray flow to soil, mill metathesis concretion action, and penetrate, split, crush action of serum to soil, etc. third, the paper in - depth study design calculate of composite grouting, design of composite grouting technic parameter

    其次，本文對復合注漿法加固地基的作用機理進行了深入的探討，包括高壓噴射流對土體的噴射切割作用、漿液與土的攪拌置換固結作用以及漿液對土體的滲透、劈裂、擠密作用等問題。第三，本文對復合注漿的設計計算、注漿技術參數的設計進行了深入的研究。
  8. 3 design and compute for mightiness tighten spring

    3強力壓緊彈簧的設計計算。
  9. This article designs the calculation and the structure of the mechanism, using elastic and vertical raiser mechanism ( papilionaceous spring ), and makes concussion test towards the special failure of take up

    採用彈性垂直托貨機構（碟簧式） ，對該機構進行設計計算和結構設計，並對提升機的特殊故障進行了沖擊校核。
  10. To attain the high - power, well - proportioned and steady high - energy particle beam is the base of analyzing beam loss. the factors that influence the emission performance of the filament are analyzed, and the parameters are calculated. the experiment results proved the correctness of analyses

    獲得大功率、均勻、穩定的高能粒子束是進行束流損失分析的基礎，本文分析了影響燈絲發射特性因素，對燈絲各參數進行了設計計算，實驗證明了分析的正確性。
  11. Of key parameters standard design. it predigests the design and improves the design veracity

    既簡化了設計計算，又提高了設計的準確性。
  12. While the system comes into jumping vibration state, the system respondence becomes small again

    四、以實例方式提出了一種小型平板振動夯的設計計算方法。
  13. But to deep - lying diversion runnel, there are a lot of problems to be resolved not only hi design theory but also in techniques

    然而對深埋引水隧洞，無論是設計計算理論，還是施工建設技術，都處在探索階段。
  14. The present findings of semi - rigid connections, the method for design of beam - to - column connections in the codes from china and other countries, and the character about semi - rigid connections, were briefly introduced in this paper. the simulated method of the m - r relation curve of semi - rigid connections, the computing equations about the initial stiffness and moment capacities of two kinds of top - seat angle connections, with and without double web - angle, were discussed

    本文簡要地介紹了半剛性節點的研究現狀、各國規范樑柱連接的設計計算內容和方法、樑柱連接的類型和半剛性連接的特性，探討了頂、底角鋼、頂、底角鋼帶雙腹板角鋼兩種半剛性連接的m - _ r特徵曲線及其擬合方法，頂底角鋼連接、帶雙腹板頂底角鋼連接初始剛度以及彎矩承載力的計算公式。
  15. A kind of mechanical patterned step - less variator with specified range of application has been introduced. the composition, working principle of this mechanism and its designing calculation were expounded

    摘要介紹了一種具有一定應用范圍的機械式無級變速器。闡述了該機構的組成、工作原理及其設計計算。
  16. In this paper, several important points which include design of active damper, model of the system, computer simulation, theoretical analysis and experiment study of the theory will be explained

    本文比較系統地提出了一套全新概念的液壓半主動懸架結構，它包括建模分析、結構設計、計算機模擬、理論分析計算、實驗研究等方面的內容。
  17. There are mostly a few aspects that fully analyse for design and compute for aira : 1 design and compute for spring of rectangle section

    對自動調整臂的設計計算作了詳盡的分析，主要以下幾個方面： 1矩形截面力和彈簧的設計計算。
  18. We can say that it can develop the usage of soil nailing wall fill the rank of piles disadvantage a bright future of developing and using. the development, application, advantage and disadvantage about the " prestress anchor ribbed beam support system " is introduced in chapter 1 : it " s supporting mechanism and structural feature is introduced and compared with the soil nailing walls and un - embedded rank of piles in chapter 2 ; design and computer steps and more details about the design methods of the support system are introduced in chapter 3 ; the two important parts named draperies and anchors are introduced on their construction technology in chapter 4 ; three foundation trenches " instances with different depth in different soil are showed in the last chapter 5

    本文在第一章概論部分介紹了「預應力錨桿肋梁支護結構」的發展、應用和優缺點；第二章分析其支護機理、結構特點，並與土釘墻和無嵌入排樁多錨支護進行了結構受力對比分析；第三章介紹該支護結構的設計計算方法步驟，詳細介紹了支護結構各部分的設計方法；第四章介紹預應力錨桿肋梁支護系統最重要的兩個部分：帷幕和錨桿的施工技術；第五章介紹了不同土層不同深度的有代表性的三個基坑工程實例。
  19. Due to the complexity of the behavior of pile capping beam widely used in the construction, the inverted continuous beam method is usually adopted in design methods to simplify the computation

    條形樁基承臺梁在我國現代建築工程中應用極為普遍，其設計計算大多採用倒置的連續梁模式進行簡化計算。
  20. Finally, by the analysis of the highness of beam - bridge, the most dangerous section and the abutment cons truction of the circular hole castellated beam, the design and calculating method of the beam is given to promote the application of the beam

    最後，通過對圓孔蜂窩梁的梁橋高度、驗算截面以及支座構造措施等的分析，總結出圓孔蜂窩梁的設計計算方法，以促進這種梁的設計與應用。
分享友人
分享到 Line

分享到臉書