試作鑄件 的英文怎麼說
中文拼音 [shìzuòzhùjiàn]
試作鑄件
英文
pilot castings-
Abstract : this paper introduced the induction hardening experiment of components ? the gear - park and the drive support sprocket. give some advise on the pearlitic malleable iron ' s induction heat - treatment, and show coil design intending to meet the harden profilc according to the drawing
文摘:本文介紹變速箱零件? ?駐車齒輪和鏈輪支架的感應淬火試驗工作,提出對可鍛鑄鐵感應淬火中值得注意的問題及針對這兩種零件的特殊硬化層要求而設計的感應器。Because of the limitation of experimental conditions we failed to form foam lead grid in the experiment. copper draw net is used as anode grid and it can improve to some extent the utilization of pam. due to human errors in the experiment we have not used the same discharge current density
在實驗中我們試圖通過鑄造法、電鍍法和還原法等一系列的實驗辦法製作泡沫鉛板柵,由於實驗條件的限制,沒能夠成功制得泡沫鉛,而在使用銅拉網作為正極板柵的時候,能夠使電池的正極活性物質利用率有提高,但由於實驗時候的失誤,沒能夠使用相同的放電電流密度進行放電,我們無法利用實驗數據比較出具體能提高的數字。Vitreous and procelain enamels for cast iron ; production of specimens for testing
用於鑄鐵的釉瓷和搪瓷.試件的製作Secondly, choose the sample component, as different particle match of tungsten carbide and specifically heat treatment craftworks of solution and aging manufacture test piece, watch metallurgical structure of the test piece and do the tests of hardness and tension, at last do the abrasive wear test on the dynamic load abrasive wear test machine, analyze test datum, from the test data, conclusions are arrived that the hardnees of composite - alloy can be improved and wear - resistance be better by adding cr and other elements according to a given ratio
本文對rp中速磨煤機耐磨件進行了運行與磨損情況分析,研究、提出了制備磨輥和盤瓦復合合金成分配比;並對製作的試件進行了固溶、時效等特定的熱處理工藝,觀察試件金相組織,進行機械強度試驗,最後做磨料磨損試驗,對磨損失效機理進行了深入的研究分析,對其耐磨性能與低合金鋼、高鉻鑄鐵進行了對比。When the data of logistics in current process are used for input of simulating logistics in future 100 % continuous casting process, supply of hot metal from iron - making process may not satisfy the needs of 100 % continuous casting on raw materials. because planning scheme in continuous casting process depends greatly on smelting scheme in convertor vessel, it is important for operator to balance raw materials supply, smelting and casting in order to realize the scheme of 100 % continuous casting. when some equipment are work abnormally, mixer of hot metal and lf furnace can be used for logistics buffer
用攀鋼煉鋼生產數據對模擬軟體系統進行的測試和模擬研究結果表明:模擬系統的隨機數發生演算法可以實現對作業時間的依分佈隨機抽取;在相似的輸入條件下,模擬結果與實際生產物流的時間分佈規律基本吻合,達到了模擬軟體設計的預期目標;若以攀鋼提釩煉鋼廠現工藝的鐵水輸入作為全連鑄后的輸入條件,則現工藝的物料供應能力可能難以滿足全連鑄生產的要求;連鑄機的連澆計劃對轉爐爐次計劃的編制有很高的要求,合理安排來料、煉鋼與澆鑄三者間的物流平衡關系將是保證全連鑄作業的重要條件;當出現設備異常情況時,可以利用混鐵爐與lf爐站前等待作為物流緩沖池,通過延長系統的平均物流時間來緩解因設備檢修和故障等擾動所造成的影響,確保生產的順利進行。分享友人