試探電荷 的英文怎麼說
中文拼音 [shìtàndiànhé]
試探電荷
英文
probe charge-
First, a simple discussion for the mechanism about electrostatic atomization of the liquids has been given ; then the paper theoretically analyzed waving course, liquid drop producing course, and the liquid drop diffusing course in electrostatics atomization process., gave an analysis about the methods about carrying charges to the liquid drop, and analyzed that liquid with high electrical conductivity can be carried charges and atomized by electric field, while the isolated liquid with low electrical conductivity can be charged fully with the soakage electrode and inducing charge methods. at last the paper designed and configured the experimental equipment, conducted the atomization experiment to the three liquid medium - kerosene, emulsifier and alcohol under the same environment, handled the experimental results, then summarized the relationship between liquid electrostatic atomization effect and liquid surface tension, electronic conductivity and viscosity, along with the influence of voltage to electrostatic atomization and so on, found out the liquid atomization rule in high voltage electrostatic field
首先,對液體介質的靜電霧化機理作了初步的探討,理論上分析了液體霧化過程中射流區、波紋區、霧滴區和霧滴擴散區;然後對液體荷電方法進行了研究分析,對于高電導率的液體,場致荷電和接觸荷電可以使其霧化,而對于電導率較低的絕緣液體,需用浸潤電極荷電和感應荷電方法使其充分帶電;最後,根據前面的研究分析,設計和組裝試驗裝置,在同一環境下對煤油、乳化劑、酒精三種不同液體介質進行高壓靜電霧化試驗,並對試驗結果進行分析處理,總結出液體靜電霧化與液體表面張力、電導率和粘度的關系及電壓對液體靜電霧化的影響等,得出高壓靜電場中液體霧化的一般規律。Abstract : experiments were made on a ultrasonic machining tool with work - piece adhered to ultrasonic transducer head, to machine micro - holes on hard and brittle materials such as soda glass and si, to study the effects of tool materials , work - piece materials , amplitude , machining load , slurry concentration , tool length and the size of work - piece on machining rate and wear ratio. in this experiment, the micro - tool was made through wedg
文摘:通過以wedg放電加工手段製作微細超聲加工用工具,在採用工件加振方式的微細超聲加工機上對碳酸玻璃、半導體硅等硬脆材料試件進行微孔加工的實驗,來探討在某一特定加工條件下工具材料、工件材料、工件的振幅、加工靜載荷、磨料懸浮液濃度、工具長度及工件尺寸等重要因素對加工速度、工具損耗率的影響,為微細超聲加工技術的實用化提供參考依據。In the master thesis, the fatigue characteristics of the ferroelectric films under thermal load and electrical load were investigated. the thermal load was induced by a pulse laser beam of nd : yag and the electrical load was made by rt6000s ferroelectric tester t o act on the films respectively. the effect of thermal or electric loads on the films properties was discussed
本文對鐵電薄膜在循環的熱載荷和電載荷作用下的疲勞特性進行了研究,分別用nd : yag脈沖激光器模擬熱載荷、用rt6000s鐵電測試儀模擬電載荷作用於鐵電薄膜,根據實驗結果探討了這兩種載荷對鐵電薄膜性能的影響。Test procedures for amplifiers and charge - sensitive preamplifiers used with detectors of ionizing radiation
用於電離輻射探測器的放大器和電荷靈敏前置放大器的測試方法Firstly, the experience of cfrm study is summarized and experiments are carried out to improve the preparation technics and to get the appropriate proportion of the materials used. secondly, the factors, which affect the conductivity and stability of cfrc, are investigated. and its smart property is studied with different cf contents and loading directions, and under elastic loading cycles
其次,通過試驗,探討了碳纖維含量、水灰比、骨料粒徑、齡期、極化效應、電極形式等對碳纖維混凝土導電性、穩定性的影響;研究了碳纖維摻量、加載方向等對碳纖維混凝土機敏性的影響;並研究了在彈性范圍、循環荷載作用下,材料的壓敏性。It analyzes the factors such as the partition of all the same layer, net power flow and distribution level to optimized routing adjustment of reactive power and voltage regulation of all power plants and substations, including local and globe. it makes power flow available and meet the need of the reactive power balancing and the reverse voltage regulation by combining the reactive power balancing principle of voltage - grading & district - dividing and local reactive power compensation with feasible power flow regulation, the reverse voltage regulation of central point voltage
該方法將無功的分層分區平衡與就地補償原則以及中樞點電壓的逆調壓原則引入到潮流的可行解調整策略之中,通過全網同層區的劃分及其網路潮流和負荷水平的計算分析,來實施對各發電廠和變電站的電壓與無功的全局或者局部的試探調整,以保證潮流的可行,並盡可能滿足無功的合理平衡與電壓的逆調壓要求。分享友人