試操縱 的英文怎麼說

中文拼音 [shìcāozōng]
試操縱 英文
trial maneuvering
  • : 名詞(古代占卜用的器具) astrolabe
  • : Ⅰ動詞1 (抓在手裡; 拿; 掌握) hold; grasp 2 (做; 從事) act; do; operate 3 (用某種語言、方言說...
  • : Ⅰ動詞1 (釋放; 放走) release; set free; let go 2 (放任; 不約束) indulge; give oneself up to; l...
  • 操縱 : 1. (控制; 開動) operate; control; roll; steer 2. (支配;控制) rig; manipulate; govern
  1. Design philosophy of hardware and software is established. the paper bases control algorithm of operator and control program diagram on thorough investigation into truck crane operation reliability action flow, which makes sure of accurate and effective control over handle and accelerograph and achieves test process automatization

    文章在深入研究汽車起重機作業可靠性驗動作流程的基礎上確定了對執行機構的控制演算法,並給出控製程序框圖,準確有效地實現了對手柄及油門的控制,達到驗過程自動控制的目的。
  2. Development of the automobile esp testing table

    汽車穩定性測臺架開發
  3. Surface boxes and ground plates ; requirements and testing ; dvgw code of practice

    地面裝置和地上蓋板.要求和驗. dvgw實施規程
  4. Modeling and measurement of the motor hand brake motivator shift

    汽車手制動機構位移的模型與測
  5. Manipulate mechanism with concentrative link lever has important significance to improve maneuverability of bulldozer currently. this thesis includes : designing manipulate mechanism with concentrative link lever and simply calculating force and displacement for operation, based on the referring existing manipulate mechanism of bulldozer ; using high - grade 3 - dimensional plotting software ug ( unigraphics ) to sculpt ; using adams ( automatic dynamic analysis of mechanical systems ) to establish virtual prototyping model and do kinematic simulation. the results verify the rationality of this mechanism and provide the basis for trial - manufacture of physical prototyping and betterment design

    本文做的主要工作是:參考推土機原有的變速轉向機構,設計了集中連桿機構並進行力和行程的簡單計算;使用高檔三維造型軟體ug (全稱unigraphics )進行推土機集中連桿機構的造型設計;應用機械繫統運動學/動力學模擬分析軟體adams ( automaticdynamicanalysisofmechanicalsystems )對所設計的機構建立虛擬樣機,並進行運動學模擬分析,驗證了機構設計的合理性,為物理樣機的制和改進設計提供了依據。
  6. Mopeds and motorcycles - method of driving test

    機動自行車和摩托車.驗方法
  7. In addition, the second part of text adopts mmg segregative math model and correlative series test result and built ship manoeuvre movement equation of one propeller and one rudder ocean transport ship in still deep water. besides, the text used math model to workout calculated program that was modeled on ship ' s turning trajectory and zigzag manoeuvre

    另外,論文後半部基於mmg分離式數學模型及相關的系列化驗結果,建立了單槳單舵海洋運輸船舶在靜水中的船舶運動方程,利用數學模型,編制了計算程序,對船舶回轉運動、 z形運動進行了數學模擬。
  8. Controllability and stability test procedure for automobiles - pylon course slalom test

    汽車穩定性驗方法蛇行
  9. Manoeuvring of ships - part 8 : zig - zag test trial z - test trial

    船舶的.第8部分: z字形運行
  10. Aerospace series - circuit breakers - test methods - actuator button travel

    航空航天系列.斷路器.驗方法.調整片按鈕調動
  11. Aerospace series - circuit breakers - test methods - part 501 : actuator button travel

    航空航天系列.斷路器.驗方法.第501部分:調整片按鈕調動
  12. Aerospace series - circuit breakers - test methods - part 501 : actuator button travel ; german and english version en 3841 - 501 : 2004

    航空航天系列.斷路器.驗方法.第501部分:調整片
  13. As a result, many countries ask new - built ships and watercrafts that enter water area of their countries to put in maneuverability calculating book and correlative test record

    為此,許多國家都要求新建造的船舶及進入該國水域的船舶都要提交性計算書和相關驗報告。
  14. One week interval. sms requires that every crew on board is capable of operating it. the fourth engineer must take charge of maintenance and repair work

    您多長時間驗一次救生艇機?誰負責艇機?誰負責維護和修理艇機?
  15. How often should you test lifeboat engine ? who takes charge of the operation ? who takes of maintenance and repair work

    您多長時間驗一次救生艇機?誰負責艇機?誰負責維護和修理艇機?
  16. Manoeuvring of ships - part 3 : pull - out trial

    船舶的.第3部分:撥拉
  17. Trial code of manoeuvrability for free running submarine model

    潛艇自航模驗規程
  18. Measurement methods for ship speed and maneuverability with dgps

    船舶航速和性的dgps測方法
  19. Method for performing captive - model test of submarine maneuverability

    潛艇性水動力模型驗方法
  20. Trial true vector

    試操縱真矢量
分享友人