試樣分取器 的英文怎麼說

中文拼音 [shìyàngfēnqǔqì]
試樣分取器 英文
sample splitter
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 樣 : Ⅰ名詞1. （形狀） appearance; shape 2. （樣品） sample; model; pattern Ⅱ量詞（表示事物的種類） kind; type
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 取 : Ⅰ動詞1 （拿到身邊） take; get; fetch 2 （得到; 招致） aim at; seek 3 （採取; 選取） adopt; assume...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  1. The structure of air - blast pipe was improved on. an orienting object was installed based on theoretical analysis, that increase the spraying span. it has been found that both spraying span and droplets uniformity improved, by installing the orienting object. according to the results of a great number of experiments, orderliness of droplets diameter along the spraying span was researched, and rational spraying span of air - assisted sprayer was suggested

    通過試驗檢驗噴霧機樣機的噴霧性能，並提出對各項參數的優化設計方案。通過正交試驗和對比試驗對霧滴取樣，證明導流器的安裝不僅增加了噴幅，而且還提高了霧滴均勻性系數。根據大量試驗的結果分析，找出了霧滴直徑在噴幅方向上所呈現的變化規律，並提出了合理的噴幅范圍。
  2. Through the theory of light radiation and intensity, we can use the fewest leds to satisfy the luminous intensity demand. through image segmentation theory, we can accurately pick module up from the test stripe when it is put in wrong directions. through image processing theory, we can acquire correct information and avoid the bad effects from the asymmetric chemistry reaction and instability of the devices

    用光的輻射和強度理論，我們計算出了獲得足夠圖像強度所需的最少光源;用圖像分割理論，我們在試紙條傾斜放置或有垂直方向上的偏移時，準確地提取出了各模塊的數據;用平滑濾波和均值濾波理論，我們濾除了由於反應不均勻及硬體設備不穩定帶來的噪聲;用交遇區設計線性分類器的方法，我們降低了有限樣本設計線性分類器帶來的誤差，提高了檢驗準確度。
  3. With the acceleration of extinction of species, biodiversity conservation is extensively concerned. the extinction of species is concerned with the degree of threat by biotic and abiotic factors. so, taking action to preserve plant species is very necessary and paramount before their extinction. one of the most effective biological techniques to conserve the biodiversity is the establishment of genebanks, i. e. ex situ conservation. the elucidation of various factors that regulate seed viability and vigor in storage is essential. an ideal condition to prolong the longevity is mainly depended on seed water content, temperature, humidity and types of containers used during storage. the optimum stage of seed maturity, harvesting techniques and processing, in addition to physiological features such as degree of dormancy, also play key roles in seed storage. certainly, desiccated seeds deteriorate with time even under extremely good genebanking conditions. according to seed storage behavior, it is necessary to consider three principal factors : storage environment, storage duration and plant species which will affect seed survival under good genebanking conditions. the present review is an attempt to discuss the importance of the aforementioned aspects of seeds in detail in order to conserve plant germplasms ( especially wild rare and endangered plants ) for ex situ conservation through seed - gene bank

    一個物種的滅絕是與其受生物因子和非生物因子的威脅程度相關的.隨著物種的加速絕滅，保護生物多樣性受到廣泛地關注.保護生物多樣性的最有效的生物技術之一是建立種子基因庫，進行遷地保護.種子庫理想的貯藏條件主要取決于種子含水量、貯藏環境（如溫度和濕度）和貯存種子的容器.進行種子貯藏，了解種子生命力和活力的影響因子的作用機理是十分重要和必要的.除了種子自身的生理特徵外，種子的貯藏壽命與種子成熟度、收獲技術、加工處理方法也是息息相關的.即使在最適的庫存條件下，種子也會隨時間發生劣變.因此，必須根據種子特定的貯藏行為，加以考慮影響種子存活的3個主要方面（貯藏環境、貯藏期和植物種類）而選擇有效的貯藏方案.本文試圖討論種子貯藏生理的幾個重要方面及其需解決的技術問題，以便更好地通過種子基因庫，長期有效地保存植物種質資源
  4. This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

    本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。
  5. This paper ’ s background is society need, and assimilates experience of former scholar to improve on a liquid self - circulating radiator for electronic component and develops a new form of more effective compound heat pipe radiator for electron component. at the same time, which is charged respectively by four natural working substance ? ? methanol, ethanol, acetone, water and a refrigeration ? ? r123

    本文正是在這樣一個社會需求背景下，吸取前人工作經驗，改進原有電子器件液體自循環冷卻系統，並開發出一種更為有效的電子器件復合型熱管散熱裝置，分別使用了四種天然工質? ?甲醇、乙醇、丙酮、水和一種製冷劑? ? r123進行試驗。
  6. Base on the ideal sampling theories, fiber length distributions and figrogram of samples taking from the ideal sliver by actual sampler are studied, and factors affecting the distributions curves are researched into, some basic requests and references of sampling are concluded for the future developing of sampler

    摘要在理想的截面取樣理論基礎上，進一步研究了具有一定寬度的取樣夾持器以一定角度從「理想棉條」中取樣時試樣的理論分佈及照影機曲線，並結合實驗分析了取樣影響因素；根據研究結果得出了棉纖維長度測試的取樣要求，為取樣器的進一步開發提供了參? 。
  7. The thesis mainly investigated the bati _ 4o _ 9 ( bt _ 4 ), which has the lowest dielectric loss in ba - ti system, and ( ba, sr ) tio _ 3, the a position substitute compound of batio _ 3. the dielectric properties of bt _ 4 / bst with different preparation way and different elements doping were investigated. a archimedes method, xrd, sem, impedance analyzer, network analyzer and hakki - coleman method were used to investigate the density, phase formation, microstructure, dielectric properties and doping mechanisms

    本論文以在ba - ti系中具有最低介電損耗的bati _ 4o _ 9 （ bt _ 4 ）高頻介質陶瓷和batio _ 3a位sr取代而得的（ ba ， sr ） tio _ 3 （ bst ）高頻介質陶瓷作為研究對象，對不同粉體制備方法制備的bt _ 4 / bst高頻電介質材料進行不同元素的摻雜，運用阿基米德方法， x射線衍射分析儀，掃描電子顯微鏡和阻抗分析儀，網路分析儀， hakki - coleman法等方法手段和測試儀器測試燒成樣品的密度，相組成情況，微觀結構和介電性能，探討造成介電性能起伏的形成機理。
  8. " whole - reservior sampling tester " and " multi - layer sampling tester for producing wells " are large - sized and new - style formation test apparatuses used for exploration wells and producing wells, which are automatic and digital

    摘要全儲層取樣測試器和生產井分層取樣測試器是用於油氣裸眼勘探井和生產井的自動化、數字化的大型新式地層測試儀器。
  9. One set of equipment for gas catalystic reconstruction developed by us own is illustrated in the following figure, in which tar sampling system is also included. in this thesis, the experiment system : biomass tar catalytic pyrolysis, which overcomes the disadvantage of mixture of some typical compound. and some improvement was made to adapt the characters of tar content of china

    該試驗裝置克服了當前生物質焦油催化裂解研究中採用焦油的某一種組分或者幾種組分的混合物作為其模擬化合物的缺點，以熱解反應器產生的生物質氣為焦油來源，在實驗中對現有的焦油取樣分析方法進行了改進，提出了適合我國生物質特點的焦油成份分析方法。
  10. It has been shown that this updated sampling and measurement method, which can measure the content of tar and dust individually, appears much more precise and credible, particularly aiming at the characteristic of heavy tar and dust content in biomass gas. this clarification system that adopts two - level shell and tube condensers and one tar removal filter, has the advantages of high removal efficiency ( 97 % ~ 98 % ) and low operating cost. besides, it has been made more environmentally friendly considering that wastewater from condensers has measured up to related effluent state standards after being disposed in tar clarifier - tank

    多次試驗表明：針對生物質氣浙江大學碩士學位論文含焦油灰塵量大的特點，改進的生物質焦油取樣測量法可實現焦油和灰塵的分離，有較高準確性和可靠性；採用二級管殼式冷凝器與一級乾式過濾器結合的燃氣冷凝凈化系統不但凈化效率高（ 97 98 ） 、運行費用低，而且含焦油廢水二經過澄清池澄清處理后可達到國家相關污水排放標準，避兔了濕式凈化系統的水污染；兼顧凈化效果、經濟性和減少污染考慮，採用以半焦為吸附材料的于式凈化系統可以達到炊用燃氣對焦油含量的要求。
  11. Since that the choosing line hardware for the neutral ungrounded system has just passed part of the dynamic simulative test, matlab software was chosen to do a lot of simulative tests on single phase - to - grounding fault. and the simulative sampling ratio is almost the same as the hardware ' s. because there is a low wave filter in the hardware, i choose the db15 wave - let to carry out the multidimensional decomposition on the sample by the method of one dimension discrete wavelet in order to obtain low frequency signal including the high frequency transient information on single phase - to - grounding fault

    鑒于實驗室已有的小電流接地系統選線硬體的研製只通過了實驗室里的動模試驗，故選用matlab軟體對小電流接地系統進行大量的單相接地故障模擬試驗，模擬的采樣率和硬體基本一致，由於硬體中帶有低通濾波器，故在進行采樣數據的morlet小波分析時先採用db15小波對采樣進行一維離散小波的多尺度分解，使得分解得到的低頻信號剛好包括了小電流接地系統單相接地故障時的暫態高頻信息，然後對這一信息再繼續進行小波演算法分析，分析結論表明利用變換后的實部、虛部和模值能夠較準確的實現單相接地故障時的故障選線和暫態高頻分量的提取。
  12. Cascade representation is adopted to represent face rapidly to improve the fast face representation from coarse to fine, from simple to complex, and to improve the speed and accuracy of the processing. subsequently, designs of the classifiers are described in three aspects. first of all, some common classifiers are firstly discussed such as sf ( sign function ), nn ( nearest neighbour ), adaboost, svm ( support vector machine ), ann ( artificial neural network ) etc. then appropriate classifiers for face detection and recognition are selected

    通過對pca 、 lda 、 gabor和like - harr人臉表示方法的研究，分別為人臉檢測和識別選取了較為穩定而準確的人臉表示；初步嘗試了利用adaboost分類器進行特徵選擇從而消除冗餘特徵，並且提出了採用級聯表示方法快速表徵人臉，從而實現由粗到精、由簡單到復雜的快速人臉表示，這樣既提高了人臉的檢測和識別的速度，還有利於檢測率和識別率的提高。
  13. Light can be guided into the fiber and transmitted to the remote end where a sensor inserted into sample was fixed. the on - line information can be obtained with the instrument constituted by electron conversion, analog - to - digital transform and data analysis system

    光輻射聚焦進入光纖到達光纖遠端位於試樣中的傳感器，實時獲取分析物信息，由檢測器及計算機介面進行模數轉換和數據處理。
  14. Ambient air quality - diffusive samplers for the determination of concentrations of gases and vapours - requirements and test methods - part 3 : guide to selection, use and maintenance

    環境空氣質量.氣體和蒸氣濃度測定用擴散取樣器.要求和試驗方法.第3部分:選擇使用和維修指南
分享友人
分享到 Line

分享到臉書