試驗板 的英文怎麼說
中文拼音 [shìyànbǎn]
試驗板
英文
breadboard試驗板結構 breadboard construction; 試驗板實驗 breadboard experiment-
Electronics engineers build their models with breadboard circuits, using the laws of physics to determine expected values for various properties and then precision instruments to measure actual values
電子學工程師通過電路試驗板建造模型,運用物理學法則確定不同屬性的期望值,然後使用精密儀器來測量出實際值。Standard test method for an imaging technique to measure rust creepage at scribe on coated test panels subjected to corrosive environments
用成像技術在腐蝕環境中測量塗覆試驗板劃痕處銹蝕蠕變的標準試驗方法Exterior building paints. preparation of test panels of steel - cement - silica
建築物外部塗料.鋼化水泥硅土試驗板材的制備Then the thermal visualizations of jet impingement cooling with single or double row holes inside semi - enclosed ribbed channel are measured by using infrared camera and the effects of flow and geometry parameters on convective heat coefficients are obtained. the results show that : the impingement cooling effectiveness of ribbed surface is affected greatly by the jet - to - surface spacing, and the best effectiveness is achieved under the jet - to - surface spacing equals to 1. the correlation formulas of impingement heat transfer characteristics to the parameters are finally concluded and in good agree with the experiment data
最後,對單排、雙排沖擊孔試驗板在半封閉通道展開了流量系數的研究,在變化各種幾何因素及流動因素的情況下由實驗得出了沖擊孔流量系數值,討論並分析了各種因素對流量系數的影響程度,建立了沖擊孔流量系數的準則關系式,與實驗結果對比表明:該準則關系式與實驗實測數據吻合較好,精度較高,有較高的工程應用價值。The phenomena can be observed in the tests low seepage pressures can easily form passageways behind the waterproof layer if there is no drainage layer or the drainage layer is blocked in the single - shell test slab ; the waterproof layer can resist higher seepage pressure if there is no drainage layer or the drainage layer is blocked in the double - shell test slab ; the seepage water can be controlled and drained away in the drainage layer by the water proof layer only if there is unblocked drainage layer behind it in the double - shell test slab
由試驗可見,在單層試驗板中沒有排水層或排水層不通暢時,較低的水壓就能在防水膜后形成滲流通路;在雙層試驗板中沒有排水層或排水層不通暢時,防水膜能抵抗一定程度的滲漏水壓;只有在雙層試驗板中的排水層暢通時,防水膜才能有效地將滲漏水控制在排水層中排走。Use roller to roll one of end of tape in order to adhere to tescified load on lower end. measure the distance of slide after a certain time. if drop it is time to evaluate tape ' s retention
將膠帶之一端以滾輪輾壓,使之粘于試驗板,一端懸吊規定之重量,經一定之時間后,量測膠帶下滑之距離,如中途掉落,則記錄時間,用以評定膠著保持力Fibre - reinforced plastics - methods of producing test plates - filament winding
纖維增強塑料.試驗板的制備方法.長纖維纏繞Fibre - reinforced plastics - methods of producing test plates - general conditions
纖維增強塑料.試驗板的制備方法.通用條件Fibre - reinforced plastics - methods of producing test plates - moulding of gmt stc
纖維增強塑料.試驗板的制備方法. gmt stc的模製Fibre - reinforced plastics - methods of producing test plates - wet compression moulding
纖維增強塑料.試驗板的制備方法.濕壓縮模塑法Fibre - reinforced plastics - methods of producing test plates - resin transfer moulding
纖維增強塑料.試驗板的生產方法.樹脂轉換模塑法Fiber - reinforced plastics - methods of producing test plates - part 1 : general conditions
纖維增強塑料.試驗板生產方法.第1部分:通用條件Fibre - reinforced plastics - methods of producing test plates - compression moulding of smc and bmc
纖維增強塑料.試驗板的生產方法. smc和bmc壓模Fibre - reinforced plastics - methods of producing test plates - part 1 : general conditions
纖維增強式塑料製品.試驗板的生產方法.第1部分:一般條件Ships and marine technology - fire resistance of hose assemblies - requirements for the test bench
船舶和航海技術.軟管組件的抗燃性.試驗板的要求Fibre - reinforced plastics - methods of producing test plates - contact and spray - up moulding
纖維增強塑料.試驗板的制備方法.接觸模壓法和噴射成形法Fibre - reinforced plastics - methods of producing test plates - part 5 : filament winding
纖維增強式塑料製品.試驗板的生產方法.第5部分:長纖維的纏繞法Fibre - reinforced plastics - methods of producing test plates - injection moulding of bmc and other long - fibre moulding compounds - small plates
纖維增強塑料.試驗板的生產方法. bmc和其他長纖維化合物的注射模塑法.小型試驗板Fibre - reinforced plastics - methods of producing test plates - injection moulding of bmc and other long - fibre compounds - general principles and moulding of multipurpose test specimens
纖維增強塑料.試驗板的生產方法. bmc和其他長纖維化合物的注射模塑法.多用途試樣的一般原則和模製Fibre - reinforceds plastics - methods of producing test plates - part 10 : injection moulding of bmc and other long - fibre moulding compounds - general principles and moulding of multipurpose test specimens
纖維增強塑料.試驗板的生產方法.第10部分: bmc和其他長纖維化合物的注射模塑法.多用途試樣的一般原則和模製分享友人