誤差檢測程序 的英文怎麼說

中文拼音 [wùchājiǎncèchéngxù]
誤差檢測程序 英文
error detecting routine
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 誤差 : error
  • 檢測 : check; detection; test; gauging; detecting; sensing; [工業] checkout; measuring
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. ( 2 ) the liman problem is normally adopted to check the liability of numerical method. the calculation error was within 9 % by comparison with the theoretic solutions of liman problem in the following case, the dimensionless calculation length was 2 with high pressure zone 0. 8, and the dimensionless state parameters were p1 = 2, p2 = 1, p1 = p2 = 1, u1 = u2 = 0. experiment results in literature [ 8 ] were used to check the adaptability of the numerical model developed here for unconfined gas cloud explosions and the calculation error was within 13 %

    （ 2 ）數值方法的可靠性通常用黎曼問題的解析解檢驗，本文以無量綱計算區長度為2 ，高壓區長度為0 . 8 ，狀態參數為p _ 1 = 2 ， p _ 2 = 1 ， _ 1 = _ 2 = 1 ， u _ 1 = u _ 2 = 0條件下的黎曼問題解析解對所編制的爆炸場計算程序進行了考核，結果表明該程序的計算誤差在9以內；為考核本文計算模型預測開敞空間氣雲爆炸的適用性，以文獻[ 8 ]的實驗數據進行了校核，計算誤差在13以內。
  2. Fibre optic interconnecting devices and passive components - basic test and measurement procedures - examinations and measurements - measurement of the angular misalignment between fibre and ferrule axes

    光纖互連器件和無源元件.基本試驗和測量程序.檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量
  3. Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 26 : examinations and measurements ; measurement of the angular misalignment between fibre and ferrule axes

    光纖互連設備和無源元件.基本試驗和測量程序.第3 - 26部分:檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量
  4. ( 2 ) by using the methods of analytic geometry and mbs and parameter measure map along x - axes by 9 - line distinguish method, the formulas for correctly identifying the error parameters have been established

    （ 2 ）針對sk - 21數控磨床開展誤差參數檢測實驗，通過現場測量，獲得凸輪工作臺直線運動誤差和旋轉誤差數據，運用9線辨識法進行分析，經數學處理后為補償程序提供必要數據。
  5. Imposing on the abundant fwd test data, a newly pavement intensity assessment standard is come into being. recurring to the program evercalc5. 0, the common rules of backcalculation modulus are introduced, moreover, the influence of instrument measurement error and input parameters are construed. utilizing the characteristics of deflection basin, so that it can assess the intensity of whole pavement structure

    通過對豐富的fwd檢測數據的分析，提出了全新的路面結構強度評定標準；藉助evercalc反算程序，介紹了模量反算的一般規律，分析了儀器測量誤差和輸入參數對反算結果的影響，利用彎沉盆的幾何特性對路面的整體強度進行評價，並建立了各結構層動模量與靜模量間的相關關系。
  6. The operation reliability of the power transformer as the key equipment in electrical power systems, influences operation security of electrical power systems directly. the components and contents of gases dissolved in transformer oil can be used to reflects internal insulation faults of operating transformer. in order to overcome the errors caused by complex handling procedure and man - made factors using general chromatogram analysis method, author brings forward an on - line detecting of gases dissolved in transformer oil by using macromolecule polymer to separate oil and gases automatically and an information fusion technology of multi - sensors ; at the same time, in order to improve the accuracy and reliability, author uses neural networks to diagnose transformer faults

    變壓器作為電力系統的樞紐設備，其運行可靠性直接影響電力系統的安全運行；變壓器油中溶解氣體的成分和含量能有效體現運行變壓器內部的絕緣故障情況，為解決常規色譜分析中復雜的操作程序和由於人為因素引起的較大的誤差，論文提出了應用高分子聚合膜實現變壓器油氣自動分離、多傳感信息融合技術智能檢測多種氣體成分的變壓器油中溶解氣體在線監測技術，應用神經網路智能診斷方法實施故障診斷，提高變壓器故障診斷的準確性和可靠性。
  7. The calculation method of the uncertainty of the examination by error theory is introduced. the semi - automatic method to examine the digital meter by vb technique and the problems existed in the process are discussed. the program flow diagram and part of program are given

    使其具有測試、數據處理、數據存貯、證書列印、查詢文檔等功能；介紹了檢測軟體主要設計過程；利用誤差理論分析了誤差，詳細介紹了不確定度的計算方法；介紹了利用visualbasic軟體技術對數字表進行半自動校驗的實現方法及所應注意的問題，給出了程序校驗流程圖及部分程序。
分享友人
分享到 Line

分享到臉書