誤差源 的英文怎麼說

中文拼音 [wùchāyuán]
誤差源 英文
error source
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 源 : 名詞1. （水流起頭的地方） source （of a river）; fountainhead 2. （來源） source; cause 3. （姓氏） a surname
  • 誤差 : error
  1. In this paper, error sources and the relation between error source and transmission error of harmonic gear drive are deeply analyzed based on its working principle and structure. then synthesize these errors by using stochastic error theory to write out estimative formula that calculate transmission error

    本文重點對諧波齒輪傳動的運動精度進行分析研究，從諧波齒輪傳動運動誤差的產生入手，首先對誤差源進行了深入分析，然後對運動誤差進行了分析和綜合。
  2. As the range increases thermal noise tends to take over as the major source of inaccuracy.

    當射程增大時，熱噪聲將成為一個主要的誤差源。
  3. The model of influence upon the parallel between servo optic axis from the angle error of installation plans presented. whereby the theoretic analysis is carried out and the analyzing results are obtained. the method of obtaining the angle error through measuring the installation plans with three - coordinates measuring device and fitting the measurement data is put forward and pave a road for lessening the influence

    對安裝面角誤差影響隨動光軸平行性的問題也建立了數學模型，以此為出發點進行理論分析，給出了分析結果；提出用三坐標測量機測量安裝面，通過擬合得到安裝面的角誤差；從而為減小這一誤差源對隨動光軸平行性的影響鋪平了道路。
  4. Three main error sources are the variation of intensities, the orientation errors associated with the configurations of the polariscope and the initial stress existing in the model. a quantitative method is presented to analyze and estimate the influence of different error sources on the final isoclinic results calculated by fcpst or the other pst

    本文提出它們影響五步彩色相移法的定量誤差分析方法；提出控制各誤差的具體指標；給出了避免或降低這些誤差源影響的措施，為合理設計製造儀器、指導實驗和保證實驗結果的精度提供了依據。
  5. On improving the precision of micromachined tuning fork gyroscope

    音叉電容式微機械陀螺的誤差源分析與消除
  6. Most of error sources can be eliminated by double differencing due to the short antenna seperations within gps based attitude determination system, multipath is the dominant error source

    Gps姿態測量中，大部分誤差源可通過雙差得到抑制或降低，多徑誤差成為主要的誤差源。
  7. Based on an analysis of the sources of errors in airborne gravity measurements, an error model is studied to constructed mathematically which can characterize the change of systematic errors, with which the network adjustment is carried out and the model parameters are determined simultaneously. and finally, the compensation of systematic errors is realized

    航空重力測量測線網平差就是在分析、總結航空重力測量的主要誤差源基礎上，研究建立反映航空重力觀測系統誤差變化規律的誤差模型，根據交叉點不符值條件，平差求解各測線上重力觀測值系統誤差改正數，然後對各測線上所有重力觀測值進行改正（補償） 。
  8. Two practical applications prove their efficiency. 3. using knowledge of adjustment with additional systematic parameters, based on an analysis of the sources of errors in airborne gravity measurements, an error model is studied to constructed mathematically which can characterize the change of systematic errors and with which three kinds of new crossover adjustment models are presented

    3 、根據附加系統參數平差的理論，在分析、總結航空重力測量的主要誤差源基礎上，研究建立了反映航空重力測量系統誤差變化規律的誤差模型，並根據三種不同的情況建立了相應的測線網平差模型。
  9. So the drift error of gyro is always the main source of error in the control and navigation system, the study of technology of measurement and compensation plays more and more important part in this field

    由於陀螺的漂移誤差是整個控制和導航系統的重要誤差源，所以，對陀螺儀漂移的測試及補償技術的研究具有越來越重要的意義。
  10. Stewart platform error model has been built up based on the simplified error source model

    針對簡化誤差源模型（含42個誤差量） ，本文建立了stewart平臺誤差模型。
  11. Secondly, according to these models, the measuring errors of the systems are decomposed into the component errors and traced to their sources, i. e. the units within the measurement system. lastly, accuracy - loss diagnosis of each system is performed based on the decomposing and tracing results of the output errors. the units are diagnosed, which are the main factors of the accuracy loss of the whole system

    在實踐上，以兩套實際的測量系統為研究對象，分別對其實際的動態測量誤差進行了建模、分解與溯源，將系統的輸出總誤差追溯到各單項誤差源? ?系統內部各組成單元所產生的誤差；而後，以誤差分解與溯源的結果為依據，分別對兩套系統進行了精度損失診斷，並分析了系統中對總的精度損失影響最大的環節，此結果可為測量系統的設計者提供系統優化設計依據。
  12. According to transfer process of target information under shipboard condition, the factors that have effect on performance of photoelectric tracking system are analyzed, and the main error sources are presented

    摘要根據目標信息在艦載條件下各個環節中的傳遞過程，分析光電跟蹤系統跟蹤性能各種影響因素，給出了主要的誤差源。
  13. Based on in - depth analysis on characteristic and function principles of psd, combined with characteristic of measured object, this article presents an new real - time measurement for symmetrical degree, guiding - groove, twining angle, inside radius of long direction pipe ; completes designing work for hardware of function module and application software ; and gives analysis and computation on error sources and uncertain - degree of measure result. based on above work, this article develops a parameter - auto - chosen, integrated and automatic measurement device for beeline degree, guiding - groove symmetrical degree, twining angle and inside radius of long direction pipe

    本文在深入分析研究psd的特點和工作原理的基礎上，結合被測量對象的特點，首次提出了長定向管導槽對稱度、纏角、內徑等實時自動化測量的一種新方法；完成了硬體功能模塊及應用軟體的設計工作；並對測量結果的誤差源及不確定度進行了分析和計算；在此基礎上研製了長定向管的直線度、導槽對稱度、纏角及內徑等參數自動、實時綜合測量設備。
  14. Basing on carefulness analysis of error source, a new measuring system for small angle is designed in this paper. with super measuring precision it can be used to replace old measuring instrument

    為減小測量誤差，在對誤差源進行仔細分析的基礎上，本文研製了一種新型的高精度小角度測量儀器，以嘗試代替舊有的測量裝置。
  15. Adopt project practical quaternion algorithm of strapdown navigation system, analyze systematic error source, emulation prove the output change of sins in there is device error of inertia and the initial condition of collimation error

    採用了工程上實用的四元數捷聯導航系統的演算法，分析了系統誤差源，模擬驗證了捷聯慣導系統在有慣性器件誤差及初始對準誤差情況下的輸出變化。
  16. In this paper, accuracy design is completed through two steps : first, we analyze the error of parallel machine tool, the joints " gap are considered by using monte carlo method, also in mis part, three kinds of error sensitivity are established to wholly reflect the error of moving platform

    在並聯機床的精度設計部分，本文在並聯機床的幾何誤差模型基礎上，利用蒙特卡洛方法綜合分析了包括鉸鏈間隙的各項誤差源對加工誤差的影響，並建立了三類誤差敏感度以全面評估並聯機床的精度特點。
  17. In this paper. the question of compound guidance about mid - long range air - to - air missle to be considered. the main contributions are as follows : first, two midcourse guidance laws are given. that is optimally predictable pn micourse guidance, which is suitable for middle range missle, and singularly perturbed midcourse guidance. which is suitable for long range missle guidance ; then two terminal guidance laws are given. that is variable structure guidance, which is suitable for passive radar guidance. and optimal guidance which is suitable for active radar guidance ; and then the error sourses of hand - off are researched, the hand - off law is given at the time ; fmally, the midcourse guidance laws and terminal guidance laws are tested by simulation, and the whole trajectory simulation are given through hand - off law, and the results are satisfied

    主要工作如下：首先研究了用於中遠程空空導彈復合制導的兩種中制導律，即用於中程導彈的最優預測比例導引中制導律和用於遠程導彈的奇異攝動中制導律，它們均有很好的中制導性能，能夠滿足中末制導的交班要求；接著研究了兩種末制導律，即用於被動雷達末制導的變結構制導律和用於主動雷達導引頭的最優末制導律，均適用於復合制導末制導段；然後分析了中末制導的交班誤差源，討論了用於復合制導的交接律；最後通過模擬，驗證了提出的中制導律和末制導律，結合提出的交接規律，在不同的情況下對中末制導段彈道進行了模擬驗證，結果證明文中提到的中末制導律能夠達到性能指標要求。
  18. The results show that instrumental error in open system is more than 8 %. the main error is owing to co2 analyzer and flowmeter. and instrumental error in closed system is more than 1. 5 %

    研究表明：開路系統最大儀器誤差通常在8以上，主要誤差源為co _ 2分析器和流量計；閉路系統最大儀器誤差通常在1 . 5以上，誤差源以co _ 2分析器誤差為主。
  19. Application on error sources surveying sea - water depths with an airborne laser sound ing system

    機載激光測深系統測深誤差源的研究
  20. The zero creep and other error source has been analysed. thereafter disposal and error compensation about horizon has been lodged, demonstrated the feasibility by practical application

    對horizon零點漂移及其他誤差源進行了分析，並由此提出了其後置處理與誤差補償方法，並通過模擬驗證了其可行性。
分享友人
分享到 Line

分享到臉書