誤差邊際 的英文怎麼說

中文拼音 [wùchābiānjì]
誤差邊際 英文
margin of error
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 邊 : 邊Ⅰ名詞1 （幾何圖形上夾成角的直線或圍成多邊形的線段） side; section 2 （邊緣） edge; margin; oute...
  • 際 : Ⅰ名詞1 （靠邊的或分界的地方） border; boundary; edge 2 （里邊; 中間） inside 3 （彼此之間） betwe...
  • 誤差 : error
  • 邊際 : （邊界; 邊緣） limit; bound; boundary
  1. Research on the method of error analysis in the prediction of smp

    邊際電價預測中的誤差分析方法研究
  2. In this thesis it was proposed to simulate the drawing, trimming, flanging by using error - adjustment method. the initial trimming lines would be adjusted and optimized in the computer by adjusting error. if the shape error between the flanging boundary line and the target is larger than prescribed, the redundant area is subtracted from the initial blank by some amount of volume along the deformation path, and the insufficient volumes are added to the initial blank by the same amount

    本文提出，利用基於變形路徑的誤差修正法（ error - adjustment ） ，結合cae技術將對初始修邊線的調試過程在計算機中進行模擬（包括拉延、修邊、翻邊、整形等）計算，通過控制翻邊后零件成型邊界與實際目標輪廓之間的尺寸誤差來優化修邊線，如果初始切邊、翻邊后的輪廓與目標體的邊界存在較大偏差，則初始切邊輪廓中多餘部分單元將沿其變形路徑以相同體積量被切除，不足部分則沿其變形路徑以相同體積進行補償。
  3. Firstly using the calculated cutting contour to cut the drawing part, then flange on the flanging mould, and then check the error for flanging part. try - out the part until it is correct. it is shown that the error of calculated cutting contour is in the range of 1mm through compared it with the correct contour

    本文將實際調試出的合格零件的修邊線與採用誤差修正法計算所得的修邊線進行對比，其誤差均在1mm范圍內，對于型面極其復雜的翻邊零件，如后地板前板，其修邊誤差也可控制在3mm范圍內，這就有效地減少了汽車覆蓋件的修邊、翻邊調試次數和周期。
  4. First of all, the emd - based wavelet threshold denoising algorithm is apllied to denoise noisy structural response data to reduce the effect resulting from noise. during the process of the empirical mode decomposition ( emd ), the two boundaries of the response signal are processed with semi - periodical ? semi - symmetrical method. subsequently, hilbert - huang transform ( hht ) is used in identifying structural intrinsic frequency

    這套技術用以解決實際工程應用中遇到的在信噪比較低情況下通過結構的響應信號來進行結構損傷識別問題，即先用基於emd的小波閾值去噪演算法對含噪結構響應進行去噪處理，以有效降低噪聲影響（在去噪的emd處理過程中，對信號的邊界採用「半周期半對稱」延括演算法來抑制邊界誤差） ，然後再用希爾伯特?黃變換（ hht ）進行結構的固有頻率識別，最後計算出結構剛度。
  5. Firstly, the causes of principle error about the spatial moment - based edge operator are explored and the principle error function on random angle of edge is proposed, some important properties about the error function are also discussed

    然而空間矩運算元採用理想二級邊緣模型的邊緣公式來計算更接近於實際的三級邊緣，由此帶來了所謂的原理誤差，而以往對于原理誤差的研究也只限於垂直邊緣。
  6. Analysis result of the definite value analysis method used in the project at present does n ' t correspond to the steady real work state of slope, it ' s income safety coefficient and real security competence of slope stabilize exists certain error. because definite value analysis method neglects influence to engineering structure of random existing of the effect of loading ( slippery moment ) and resists strength ( resist the slippery moment )

    目前工程中使用的定值分析方法由於忽略了荷載效應（滑動力矩）及抗力（抗滑力矩）計算中各要素實際存在的隨機性質對工程結構安全性的影響，所以分析結果與邊坡穩定的實際工作狀態不符，所得安全系數與真正的邊坡穩定安全性水平之間存在一定的誤差。
分享友人
分享到 Line

分享到臉書