調制控制系統 的英文怎麼說

中文拼音 [diàozhìkòngzhìxìtǒng]
調制控制系統 英文
modulating control system
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. Pulse frequency modulation control system

    脈沖調頻控制系統
  2. Balanced temperature humidity control system

    平衡調溫調濕控制系統
  3. The paper introduces the design of digital variable - frequency induction motor speed modulation control systems, based on fpga

    本文提出了一種採用現場可編程門陣列（ fpga ）器件實現數字化變頻調速控制系統的設計方案。
  4. The scheduling and controlling structure for an advanced manufacturing shop is investigated based on the agile manufacturing methodology

    摘要基於敏捷製造思想研究了離散生產類型的先進製造車間的調度控制系統。
  5. The proportional flow valve control system is the most popular method among the control system of hydraulic elevators

    液壓電梯比例閥節流調速控制系統是目前液壓電梯中應用最廣泛的系統。
  6. Design of control system of high resolution switch power supply

    高解析度開關電源調壓控制系統設計
  7. The cutter location in nc generative ultrasonic grinding process for parallel ruled surface with cylindrical grinding wheel was analyzed, the structure of nc generative ultrasonic grinding device was introduced, the design of grinding spindle assembly and the spindle ' s driving scheme was also introduced, system hardware and software design had been finished

    摘要分析了圓柱磨輪數控展成超聲磨削平行直紋面時的刀具空間位置，介紹了數控展成超聲磨削成形加工機床的總體結構，論述了磨輪主軸部件設計及主軸驅動方案，實現了主軸變頻調速控制系統軟硬體設計。
  8. Technical requirements for steam turbine governing control system

    汽輪機調節控制系統技術條件
  9. This paper have introduced a kind of the design principle of wireless manage control system, the system have solved the technical baffling problem on making coding, decoding and identity identification in wireless communication and have remedied the shortcomings of traditional wireless manage system by using micro controller ( at89c2051 ) and dtmf baffling

    介紹了一種無線調度控制系統的設計原理，使用單片機（ at89c2051 ）和dtmf信令解決了無線通信中的信令編碼、解碼及身份識別等技術問題，彌補了傳統的無線調度系統的不足。
  10. Frequency conversion and speed regulation control system for shuttlecar based on plc

    的卡軌車變頻調速控制系統
  11. Simulation research on ac - dc - ac frequency conversion timing control system with high - power

    交變頻調速控制系統的模擬研究
  12. Test guide of steam turbine governing system

    汽輪機調節控制系統試驗導則
  13. Design of adjustable speed drive system with bi - directional power transferring converter for pump using motors

    泵站電機雙饋調速控制系統設計
  14. Based on above studying, current regulation control system and the electrode of application matlab software for the dc arc furnace have been simulated

    在此基礎上，應用matlab軟體對電弧爐的電極與電流調節控制系統進行了模擬。
  15. Pulse width modulation control system ; pwm control system

    脈沖調寬控制系統
  16. Dysfunction in inhibitory control systems, by decreasing the addict ' s ability to refrain from seeking and consuming drugs, ultimately results in the compulsive drug intake that characterizes the disease

    抑制控制系統的功能失調，通過降低成癮者控制尋求和使用藥物的能力，最終導致造成疾病的反復藥物攝入。
  17. Furthermore, cpld design is the necessary step for the verification of asic design. in this paper, several cpld speed modulation control systems and ip are presented

    本文設計的幾種cpld調速控制系統以及幾個ip核，一部分下載到晶元，通過實際驗證；一部分通過模擬驗證。
  18. This paper aims at the realization of variable - frequency induction motor speed modulation systems based on cpld ( complex programmable logic device )

    本文主要介紹了如何用可編程邏輯器件（ cpld ）實現變頻調速控制系統。
  19. Based on the working principle of pulse width modulation ( pwm ) control system for dc motor, the strong and weak points of two conventional pwm control modes ( limited single polar mode and bipolar mode ), when used in electric power steering ( eps ) system are analyzed, and a new pwm control, so called quasi - bipolar control mode is proposed with the correction method of its duly ratio given

    摘要針對直流電機脈寬調制控制系統的工作原理，分析了受限單極和雙極脈寬調制控制模式應用於電動助力轉向系統電機驅動時的優缺點，提出了一種「半雙極」控制模式及該模式下占空比的修正方法。
  20. This paper primarily introduced the research and implementation of ac motor variable - frequency speed regulating system based on dsp

    本文主要介紹了基於dsp的交流異步電機變頻調速控制系統的研究和實現。
分享友人
分享到 Line

分享到臉書