調整流量脈沖 的英文怎麼說

中文拼音 [diàozhěngliúliángmàichōng]
調整流量脈沖 英文
flow-rate impulse
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 脈 : 脈名詞1. （動脈和靜脈的統稱） arteries and veins2. （脈搏的簡稱） pulse 3. （像血管的組織; 連貫成系統的東西） vein
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  • 流量 : rate of flow; flow; runoff; discharge; throughput; （flow） rate; quantity （of flow）; flux
  1. Due to the complexity of the structure and control of cycloconverter - type three - phase hf link inverter for soft - switching based on phase - shift - controlled full - bridge mode, a simple and optimized vvvf control strategy is proposed. this control strategy includes : produced pwm by space voltage vector ( svm ) and equivalent carrier frequency fe = 1 / te are introduced into the pdm control of the cycloconverter ; softened equivalent pwm wave is generated at the notches of hf voltage pulses ; the harmonious control between regulating pulse width by phase - shifted angle and regulating voltage of equivalent pwm is to minimize the harmonics content of output voltage of the inverter

    西安理工大學博士學位論文針對這種前級移相全橋軟開關周波變流型三相高頻鏈逆變器結構和控制的復雜性，提出了一種實現簡單而整體優化的vvvf控制策略:將空間電壓矢量產生p姍的方法svm和等效載波頻率fe = 1 / te引入到周波變流器的pdm控制;按高頻電壓脈沖前後沿軟化等效p翎波;用移相調節高頻脈沖寬度和等效p姍調壓協調控制逆變器輸出電壓，在滿足輸出電壓條件下使諧波最小。
  2. For the measurement of analog signals such as voltage and current of astg, a filter card for pre - disposing is designed, in order to improve real - time performance, algorithms for ac analog sampling is simplified, and a compensation algorithms for phase error due to sequence - sampling is brought forward. for the measurement of impulse - width signals such as rotor - speed and rotor - position - angle, an intelligent interface card based on isa bus is designed. all programs for measure and control based on c + + are compiled and debugged and the flow for system debugging is summarized

    為了提高實時性，對交流采樣演算法進行了簡化，並提出了由於非同步順序采樣所造成的相位誤差的補償演算法；針對轉速、轉子位置角等脈沖寬度信號的測量，深入分析了測量原理，設計了基於isa總線的智能介面卡；編制和調試了基於c + +的全部測量控製程序；完成了整個系統的調試，並總結了調試方法。
分享友人
分享到 Line

分享到臉書