負荷調整器 的英文怎麼說

中文拼音 [fùhédiàozhěngqì]
負荷調整器 英文
load regulator
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 荷 : 荷名詞（蓮） lotus
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 負荷 : [電學] load; charge; weight
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. Undershoot undershoot refers to the amount by which voltage or frequency drops below the nominal value as the voltage regulator or governor responds to changes in load

    下超調下超調指電壓調整器或控制器在應對負荷變化時，電壓或頻率低於額定的量。
  2. The basic thought of the csapfba algorithm is : the edge routers perform the state management per flow, and the edge routers differentiate between the marked flows and the non - marked flows, and the edge routers insert the relevant information into the packet header by using dynamic packet state ; the core routers divide the output link bandwidth into two parts in the light of the state information of the packet header by using class - based queueing, and the core routers allocate proportionally the bandwidth to the marked flows according to their service profiles and the current network load, and the core routers allocate the bandwidth to the non - marked flows according to the principle of max - min fairness, and the csapfba algorithm can adaptively dynamically adjust the bandwidth allocation between the marked flows and the non - marked flows

    本文在csfq演算法的基礎上，提出了一種核心無狀態的自適應的成比例公平帶寬分配csapfba （ core - statelessadaptiveproportionalfairbandwidthallocation ）演算法。 csapfba演算法的基本思想是：在邊界路由器完成基於每個流的狀態處理，將所有的流分成標記流和非標記流兩種類型，採用dps技術將有關信息編碼進分組頭；在核心路由器根據分組頭中攜帶的狀態信息採用cbq策略，將輸出鏈路帶寬分成兩部分，對標記流根據當前的網路負荷按照服務規格成比例地分配帶寬，對非標記流按照最大最小公平性原則分配帶寬，並且能自適應地動態調整帶寬分配的比例。
  3. The main function of a governor is to monitor the speed deviation of a hydro turbine unit and convert it into the displacement deviation of the servomotor according to a specific characterisic. it is used to control the opening of the guide apparatus and to ensure the unit run steadily at fixed speed under a given load

    調速器的主要功用是檢測機組轉速偏差，並將它按一定特性轉換成接力器的行程偏差，藉以調整機組導水結構的開度，使機組在給定的負荷下以給定的轉速穩定運行。
  4. The governor must have provision for adjusting speed ( generator frequency ) and speed droop ( no load to full load )

    調速器必須具備轉速調整（發電機頻率）和降速降調整（零負荷到滿負荷）功能。
  5. Voltage dip voltage dip is the dip in voltage that results when a load is added, occurring before the regulator can correct it, or resulting from the functioning of the voltage regulator to unload an overloaded engine - generator

    電壓暫降電壓暫降是在負荷增加而調整器還未能進行校正時、或電壓調整器正在為過載的發動機卸載時出現的電壓下降。
  6. The research objective is to improve the control system performance through the combination of the advanced control strategy with the meaningful information mined from the history operation database. firstly, a new solution for the control performance enhancement is presented by the reference of the kdd technology. aiming at practical application, a novel boiler load control method, which combines the multiple model adaptive control strategy with the data mining technology, is put forward in this dissertation

    本文第一部分為熱工過程式控制制與數據信息採掘，研究的重點是通過先進控制策略的應用以及運行數據中發掘的有用信息，提高現有典型熱工過程式控制制系統的性能，內容包括：首次提出了借鑒數據信息採掘技術的思路和方法，用於完善現有的熱力系統優化控制方案；在此基礎上結合生產實際，提出了運用多模型自適應策略實施鍋爐負荷控制，並利用關聯規則的數據信息採掘方法，通過對燃料發熱量信息的在線診斷，優化控制器結構，同時實現鍋爐燃燒配風的自適應調整，提高負荷、燃燒控制系統性能。
  7. Nset no load opeed setting of governor

    調速器的無負荷調整
  8. The response rate speed governor to the given power signal directly affects the load regulating process of generatorset

    摘要調速器對功率給定信號響應速度，直接影響著機組負荷的調整過程。
  9. Based on the strategy the automatic voltage and reactive power control device was developed. the device is controlled by microcomputer and can adjust the ratio of transformer and switch the capacitor automatically according to operating condition

    在此基礎上，研製成功了變電所電壓無功自動控制裝置，裝置以微處理器為控制核心，可根據實測的母線電壓和負荷功率因數，自動進行主變分接頭調整和補償電容器投切。
分享友人
分享到 Line

分享到臉書