超轉矩 的英文怎麼說

中文拼音 [chāozhuǎnjǔ]
超轉矩 英文
overtorque
  • 超 : Ⅰ動詞1 （越過; 高出） exceed; surpass; overtake 2 （在某個范圍以外; 不受限制） transcend; go beyo...
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  1. Being a sort of new principle micromotor in the fronitier of science. the ultrosonic motor ( usm ) is developed at recently twenty years. utilizing the stator surface particle elliptical motion excited by piezoceeramics, the usm is drived by friction force between the stator and rotor. compared with the conventional electromagnetic motor, the ultrasonic motor has the following features : high speed, high holding torque when power is off and so on. because of it ' s characteristics, the ultrasonic motor has obtained some widespread application in robots, precise instrument, house electronical appliance, sapceecraft automobile and micromechanism

    超聲波電機（ ultrasonicmotor ）是近二十年來發展起來的一種新原理電機，其原理不同於傳統的電磁型電機，它是利用壓電陶瓷的逆壓電效應使定子的表面質點產生橢圓運動，通過定子和轉子之間的摩擦力驅動轉子運動。這種新型的電機與傳統電磁電機相比，具有響應快、不受電磁干擾、結構緊湊、低速、大扭矩、斷電自鎖等優點，因而在微型機械、機器人、精密儀器、家用電器、航天器、汽車等方面顯示出廣泛的應用前景。
  2. The results show a few grooves appear on the worn surface of the composites which contain 10 phr nano - al2o3 there are a great many grooves on the worn surface of the composites containing 20 phr. in addition the deeper cracks also appear. this shows that excess nano - al2o3 particles ca n ' t improve wear properties of pa6 ' s. the proper content of nano - al2o3 in the matrix can enable the molecular chains of pa6 to produce closed joints which resemble the physical crosslinking

    尼龍6 / a12o :復合材料的加工性能研究表明:隨著納米a12o3的加入，復合材料的熔體流動速率下降，納米a12o3含量越大，下降越明顯，即隊6 / a12o3納米復合材料的加工性能越差;隨著納米a12o3的加入，復合材料的轉矩和塑化時間都增加，當含量小於巧phr時，隊6復合材料的轉矩增加幅度不大，當含量超過15phr后，轉矩急劇升高。
  3. Secondly, the effects of the crest width of the back - emf waveform to the torque ripple in the 120 ? conduction mode are analyzed, among which the effects of the advance commutation angle to the torque ripple are quantificationally analyzed for the bldcm drives whose back - emf waveform crest width is less than 120 ?,

    其次分析了120導通方式下反電動勢平頂寬度對轉矩脈動的影響，對于平頂寬度小於120電角的非理想梯形波反電動勢，定量分析了換相超前角對換相轉矩脈動的影響。
  4. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反電動勢類似正弦的準正弦波反電動勢無刷直流電動機，本文提出一種基於六個離散位置信號的自同步svpwm （電壓空間矢量法）控制方法，用以削弱電磁轉矩脈動，分析了實現這種方法的主要控制環節，包括起動時電壓空間矢量的初始定位，阻抗角與電流超前角的合理選擇以及連續轉子位置的估計等。
  5. As novel concept actuators, ultrasonic motors have been attracting intensive attention at home and abroad with their outstanding features such as low speed and high torque, large holding torque, rapid response, light weight and compact sizes, simple structure, and no magnetic disturbance, etc. traveling wave ultrasonic motors are especially attracting researchers ’ interest for their good controllability and flexible constructions

    超聲波馬達作為一種全新的驅動器，以低速大轉矩、靜態保持力矩大、響應速度快、體積重量小、結構簡單以及無磁場干擾等優點受到國內外的廣泛關注，其中行波超聲波馬達以其控制性能良好和結構靈活等優點尤為引人矚目。
  6. It has much merit that controlling structure is simple, and the torque response of system is rapid and has no overtaking melody, and electrical energy can inpour electrified wire netting by returning unit

    它具有控制結構簡單、系統的轉矩響應迅速且無超調、電能可通過其回饋單元回饋電網等眾多優點。
  7. In this thesis, we use the random - matrix - theory to revise the following calculating methods : ( 1 ) the heat capacity and the spin susceptibility of the normal metallic small particles ; ( 2 ) the heat capacity of the conventional metallic small particles at the low temperature using the mean field approximation method ; ( 3 ) the heat capacity of the conventional metallic small particles at the vicinity of the critical temperature using the static path approximation method

    本文採用隨機矩陣理論，計算了： （ 1 ）正常態金屬小粒子的電子熱容和順磁磁化率。 （ 2 ）在平均場近似下，計算了超導金屬小粒子低溫區的電子熱容。 （ 3 ）在靜態路徑近似下，計算了超導金屬小粒子轉變溫區的電子熱容。
  8. This dissertation presents how to use the ultrasonic motor as an actuator to suppress the flutter of a two - dimensional airfoil section with a control surface. the ultrasonic motor, which features simple structure, high torque at low speed, small size, low weight and no electromagnetic contamination, is a promising actuator for the flutter suppression of small aircraft

    超聲電機以其結構簡單緊湊、轉矩/質量比大、低速大扭矩、直接驅動，動態響應快、斷電自鎖和不產生磁場且不受外界磁場干擾等優點，有望成為一種非常有前途的作動器，用於小型飛機的機翼顫振主動抑制。
  9. As novel concept actuators, ultrasonic motors have been attracting intensive attention at home and abroad with their outstanding features such as low speed and high torque, large holding torque, rapid response, light weight and compact sizes, simple structure, and no magnetic disturbance, etc, and which have been applied to many fields

    超聲波電機作為一種全新的驅動器，以低速大轉矩、大靜態保持力矩、響應速度快、體積重量小、結構簡單以及無磁場干擾等優點受到國內外的廣泛關注，並在眾多領域得到了應用。其中駐波超聲波電機具有驅動和控制電路簡單，轉速平穩，波動較小等突出優點。
  10. The experiments show that ultrasonic motors can operate under vacuum condition, but the performance is different from that under general condition, its unloaded speed decreases significantly, while the stall - torque increases a bit

    試驗結果表明，超聲電機可以在真空環境下工作，但性能較常態環境下有所變化，其空載轉速明顯下降，堵轉力矩有所增大。
  11. The innovation in this paper is list below ( 1 ) use rectangle - shape pipeline so that the inducing electromotive force could be enhanced ; ( 2 ) use alternating current whose frequency is adjustable to induce the magnetic ; ( 3 ) make the flowmeter intelligent by use the microprocessor ; ( 4 ) finish designing the ls flowmeter with utra - low power consumption

    本文的創新之處在於採用矩形測量導管大大增加微流量條件下的感應電動勢；採用輸出頻率可調的正弦波電流作為勵磁電流達到消除50hz頻干擾和減少正交干擾的目的；利用單片機等高端現代電子產品實現了電磁流量計的高度智能化及設計出真正的超低功耗的、可用干電池長期供電的ls旋轉流量計。
  12. If has been marked as output twisting force has exceeded maximum allowable twisting force that reduction device can bean, shouldn ' t full burden operate

    標記為輸出扭矩已超過減速機所承受的最大許用扭矩，不能滿負荷運轉。
  13. With the testing system, the mechanical load is applied and the relationship between the mechanical load and the revolution speed of the ultrasonic motor is studied under the vacuum condition

    通過該裝置實現了對超聲電機負載力矩的施加以及在真空環境下對超聲電機轉速、轉矩的測量。
  14. Aim at the dtc ' s blemish mentioned above and the direction of dtc technique development, the dissertation put great emphasis on the work as follows, with an eye to exalt dtc system function : ( 1 ) a new speed - flux observer of an induction motor is proposed to enhance the accuracy of flux observing, which is an adaptive closed - loop flux observer and different from the traditions. a new adaptive speed - observation - way is deduced out according to the popov ' s stability theories ; ( 2 ) to improve the performance of dtc at low speed operation, we have to exalt the accuracy of the stator flux estimation and a new way of bp neural network based on extended pidbp algorithm is given to estimate and tune the stator resistance of an induction motor to increase the accuracy of the stator flux estimation ; ( 3 ) digital signal processor is adopted to realize digital control. an device of direct torque control system is designed for experiment using tms320lf2407 chip produced by ti company ; ( 4 ) bring up a distributed direct torque control system based on sercos bus, sercos stand for serial real time communication system agreement which is most in keeping with synchronous with moderate motor control ; ( 5 ) the basic design frame of the hardware and software of the whole control system is given here and some concrete problem in the experiments is described here in detail

    針對上面提到的直接轉矩控制的缺陷和未來直接轉矩控制技術發展方向，本論文重點做了以下幾個方面的工作，目的在於提高dtc系統的綜合性能： （ 1 ）提出一種新型的速度磁鏈觀測器，新型的速度磁鏈觀測器採用自適應閉環磁鏈觀測器代替傳統的積分器從而提高磁鏈觀測的精度，並且根據popov超穩定性理論推導出轉速的新型自適應收斂律； （ 2 ）改善系統的低速運行性能，主要從提高低速時對定子磁鏈的估計精度入手，提出了一種提高定子磁鏈觀測精度的新思路? ?利用基於bp網路增廣pidbp學習演算法來實時在線地修正定子電阻參數； （ 3 ）採用數字信號處理器dsp實現系統全數字化硬體控制，結合ti公司生產的tms320lf2407晶元，設計了直接轉矩控制系統的實驗裝置； （ 4 ）提出了基於sercos總線網路化分散式的直接轉矩控制系統， sercos （ serialrealtimecommunicationsystem ）是目前最適合同步和協調控制的串列實時通信協議； （ 5 ）基本勾勒出整個控制系統的硬體和軟體設計基本框架，詳細描述一些實驗中的具體的細節問題。
  15. Analysis of electromagnetic field and electromagnetic torque performance on super high power density induction motor

    超高功率密度感應電機電磁場及轉矩特性分析
  16. Once the field is larger than the threshold field, the molecules of liquid crystal tend to the magnetic field direction and they will align to the magnetic completely under some conditions i. e. it is saturated so it is important to calculate the threshold and saturation field

    在平衡狀態下，兩個轉矩的作用相互抵消。一旦磁場強度超過一定的閾值，液晶內部的分子將更易於沿外磁場方向的排列。一定條件下分子完全沿磁場排列，即達到飽和。
  17. Furthermore, analyzing the characteristics of the ultrasonic motor in the resonant state. on the basis of theoretical research, an experimentation is made, by which we analyse the disadvantages impacting the work of traveling wave and test the relationship among pressing force, speed and pull. the results of the experimentation validate the correctness and reliability of theoretical analysis

    在理論分析的基礎上，對設計的超聲波馬達進行了實驗分析與測試，分析了影響馬達運轉的不利因素，測試了超聲波馬達不同預壓力下速度與力矩以及馬達空載時速度與頻率、速度與電壓之間的關系，驗證了理論分析結果的正確性和可靠性。
  18. The satss is an antenna pointing servo system with ultra - low speed and high accuracy, driven by a rare earth permanent magnet ( repm ) brushless dc torque motor. to reduce torque ripple, the repm brushless dc torque motor has a slotless armature, and uses sinusoidal wave driven technology

    衛星天線跟蹤伺服系統為超低速高精度天線指向控制系統，該系統使用稀土永磁式無刷直流力矩電機作為天線的驅動機構，為降低轉矩脈動，電機採用無槽電樞結構設計，並使用正弦波驅動方式。
  19. In order to make a clear technical analysis on it, author sets out research work with it ’ s principal and derives basic formula which makes it clear why crehsm can performance ultra - low speed without velocity pause

    從連續回轉伺服馬達的結構模型入手，分析了新型馬達可以實現轉速、流量和理論輸出扭矩的無脈動。針對馬達超低速的特性，作者提出了改善其性能的措施。
分享友人
分享到 Line

分享到臉書