跨線電阻 的英文怎麼說
中文拼音 [kuàxiàndiànzǔ]
跨線電阻
英文
link resistance- 跨 : 動詞1 (抬起一隻腳向前或向左右邁) step; stride 2 (兩腿分在物體的兩邊坐著或立著) bestride; stra...
- 線 : 名詞1 (用絲、棉、金屬等製成的細長的東西) thread; string; wire 2 [數學] (一個點任意移動所構成的...
- 電 : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
- 阻 : 動詞(阻擋; 阻礙) block; hinder; impede; obstruct
- 跨線 : overline跨線橋 [交通運輸] flyover; overpass; gauntree; viaduct; overpass bridge
- 電阻 : (物質阻礙電流通過的性質) resistance; electric resistance (電路中兩點間在一定壓力下決定電流強度...
-
The fact that most of these topologies need laser - trimming technique to improve the match precision to reach high cmrr is found after investigating several instrumentation amplifier topologies. in this paper, a new style instrumentation amplifier topology with current processing mode based on ccii and impedance amplifier is designed and realized
由於本論文所使用的國內工藝線沒有激光調阻技術,因此本文選擇了一種近年來新出現的一種新型儀表放大器電路結構,即使用第二代電流傳輸器( ccii )和跨阻放大器組成的電流模儀表放大器。An additional check can be made by removing the enclosure cover and momentarily placing a jumper ( or 20, 000 ohm resistor ) across terminals 9 - 10 on the control
通過拆卸外殼蓋板,並立即將跨接線(或20 , 000歐姆電阻)並聯在控制裝置的接線端子9 - 10上,能夠再次進行測試。After introduction of the tranlinear loop principal, the bjt current controlled conveyor has been designed by using mixed tranlinear loop voltage follower. as for modern integrated circuit, the model of mos transistor, the active resistance and the current mirror integrated circuit formed by mos transistor are introduced. the cmos current controlled conveyor has been derived from mixed tranlinear loop cmos voltage follower based on weak inversion operation
針對現代集成電路的工藝,本文對mos晶體管的工作原理進行了簡要的敘述,討論了有源電阻和電流鏡的實現方法,並利用mos晶體管的亞閾值特性組成混合跨導線性迴路完成對應的電壓跟隨器的設計,推導出了基於cmos技術的電流控制傳送器。With the aid of phase - mode transformation, one line fault and cross line fault positions are determined in mode - domain accurately
該演算法不受系統阻抗和過渡電阻的影響,並且消除了雙回線間耦合的影響,可用於單回線故障和跨線故障的測距。The conventional connection circuit as the figure shows for two - wired transmitter : handhold terminal palm computer and external communication interface or mainframe communication circuit cannot directly bridges in the ends of power source. but may either meet on field ends a and b or meet on the ends of load resistance b and c. in the above - mentioned case, the circuit are supplied by power source
對兩線制變送器來說,傳統的連接電路如圖所示:手持終端掌上電腦和外接通訊介面或主機通訊電路不能直接跨接在電源兩端,但既可接于現場兩端a , b上,也可接在負載電阻兩端b , c ,兩種情況下,電路都要通過電源來供電, hart規范允許負載電阻為2301100 。分享友人