路徑相加演算法 的英文怎麼說
中文拼音 [lùjìngxiāngjiāyǎnsuànfǎ]
路徑相加演算法
英文
path addition algorithm- 路 : 1 （道路） road; way; path 2 （路程） journey; distance 3 （途徑; 門路） way; means 4 （條理） se...
- 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
- 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
- 演 : 動詞1 （演變; 演化） develop; evolve 2 （發揮） deduce; elaborate 3 （依照程式練習或計算） drill;...
- 算 : Ⅰ動詞1 （計算數目） calculate; reckon; compute; figure 2 （計算進去） include; count 3 （謀劃;計...
- 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
- 路徑 : 1. （道路） way; route; trajectory; path; tail; travel2. （門路） method; ways and means
- 相加 : addition; adding; add together
- 演算 : perform mathematical calculations; calculation; calculus演算器 exerciser
-
7. based on our crsi and algorithm and double lcslm, an adaptive optical hardware system which c & n be used to model arbitrary complicated wavefront and the compensation of the wavefront can be accomplished was built. and according to the characteristic of a crs interferogram of a step wavefront produced by an lctv, the pixel - level calibration of this system is implemented
七、採用已建立的空間相位調制環路徑向剪切干涉儀及其波前重建演算法，和位相調制持性已知的兩塊液晶空間光調制器，創建了一套用於模擬產生任意畸變波前並加以檢測和反饋控制的自適應光學硬體系統，並通過臺階波前對該系統實現了像素級校準。Considering the np - complete problem, how to get the approximate optimized scheme of job - shop scheduling, and aimed at improving the efficiency of products and taking good advantage of concurrence, asynchronism, distributing and juxtaposition in multi - products and devices processing, we could divide the working procedures into the attached one which has the only precursor and subsequence and unattached one by analyzing working flow chart of job - shop, that is the working procedures are divided into two types, then the bf and the ff methods about memory scheduling in os are applied, therefore a new approximate optimized scheme is presented in the paper which could solve the common job - shop scheduling. namely, the acpm and the bfsm are applied to the classified and grouped working procedures considering the compact of the procedures and practical examples approved it. the results we analyzing and tested show that it is better than the heuristic algorithm common used, for less restriction terms, more satisfying algorithm complexity and better optimized results
針對job - shop調度問題求最優解演算法這一npc問題，本文以充分發揮多產品、多設備加工所具有並發性、異步性、分佈性和并行性的加工優勢，從而提高產品的加工效率為目標，對job - shop調度問題的工藝圖進行適當分解，使工序在一定時間段或是為具有唯一緊前、緊后相關工序或是為獨立工序，即將工序分兩類，再結合操作系統中內存調度的最佳適應（ bf ）調度方法和首次適應（ ff ）調度方法的先進思想，通過分析提出了一種解決一般job - shop調度問題的全新近優解方案：在考慮關鍵設備上工序盡量緊湊的前提下，將工序分類、對這兩類工序分批採用擬關鍵路徑法（ acpm ）和最佳適應調度方法（ bfsm ）安排工序的演算法，用實例加以驗證，並給出結果甘特圖。Secondly, in order to improve the effective of machining process, for the tool - path planning, this system come up with a way which both tool arm coordinate the movement in the same time, and used the process pattern of move toward opposite side and cutting in row, avoided the cutting tool interference effectively ; for this tool - path this paper use the way of making the cutter contact data by the second development of solidworks, and gained the cutter location data through the interference check
其次，為了提高磨削效率，在刀具路徑規劃方面，採用了雙刀協調運動、相向走刀加工的加工方式，採取變形的「之」字形走刀模式，從而有效的避免了刀具干涉，提高了加工效率。並針對上述的加工方式，對刀位軌跡生成演算法進行了研究，根據機構的特性，基於截面法生成刀具軌跡，通過solidworks的二次開發來獲得牙齒模型的三維表面數據，再利用干涉檢查生成無干涉刀位點數據。Using dead reckoning would lead to frequent state correction updates, increasing both network traffic and visible jolts ( because a quick position jump is sometimes needed when the blended replicated path differs to much from the original path )
使用導航預測演算法可能會導致非常頻繁地發送狀態校正更新包，網路流量和視覺上的震動都會大大增加（因為當混合后的復制體路徑與原始路徑相差較大時，有時候不得不做一些迅速的位置跳轉） 。The new algorithm is one of quality guided path following methods, belonging to spatial phase unwrapping methods dependent on path. its framework consists of digital weighted filtering and modulation ordering
新演算法屬于空間位相展開與路徑有關的方法中利用可靠度函數尋找優化路徑（ qualityguidedpathfollowingmethod ）的方法之一，由數字加權濾波和調制度排序構成。分享友人