軋制板坯 的英文怎麼說

中文拼音 [yàzhìbǎnpī]
軋制板坯 英文
rolling slab
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  1. The results show that " the frame - pack rolling " technology can increase the densify, avoid cracking during rolling, and effectively improve the deformability and mechanical properties of the spray deposited porous aluminum alloy sheets

    結果表明：外框限制軋制工藝提高了噴射沉積多孔材料的緻密度，避免了軋制過程中裂紋的形成，有效地改善了噴射沉積板坯的軋制性能及材料的力學性能。
  2. Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase

    研究結果表明，減薄鑄軋板坯厚度可提高鑄軋速度；隨著鑄軋速度降低、鑄軋區增大與鑄軋坯厚度減薄，軋制壓力峰值增大；隨著鑄軋輥徑增大，軋制壓力增大，因此鑄軋機力能設計參數也要相應增大。
  3. Research on technology of splitting continuous cast slab

    連鑄板坯切分軋制工藝的研究
  4. Control the quality of continuous casting and rolling thin slab

    連鑄連軋薄板坯的質量控制
  5. Ferrite rolling technology used in thin slab continuous casting and continuous rolling

    薄板坯連鑄連軋生產中的鐵素體軋制工藝
  6. Strength control of steel for cold rolling produced by thin slab continuous casting and rolling

    薄板坯連鑄連軋線生產冷軋基板的強度控制
  7. The model considers not only the slab bounce on gauge and hardness, obverse and inverse bounce on width, and the rolling length constraint of the slabs with same width, but also the reasonable arranging of warm - up materials and staple materials

    該模型不僅考慮了軋制計劃中板坯在厚度和硬度上的跳躍、板坯寬度的正反跳以及相同寬度板坯連續軋制的長度約束，而且考慮了軋制計劃中燙輥材和主體材的合理安排。
  8. In this paper, 130mm diameter hot - rolled bars ( 3 transus temperature is 798 c ) were used in experiments. the superplastic property of ti - 1023 alloy was studied systematically by the experiments of tensile and compression. the preparation method of fine - crystalline structure and the processing parameters of superplastic forging are optimized

    本文以130mm熱軋棒材為原材料，通過超塑性拉伸和超塑性壓縮試驗，對ti - 1023合金的超塑性進行系統研究，研究坯料細晶組織制備方法，優化超塑成形工藝參數，為高筋薄腹板復雜形狀ti - 1023合金鍛件超塑性等溫模鍛工藝的制定提供試驗依據。
  9. Spray deposited porous aluminum alloy sheets easily have surface and edge crack when they are directly rolled due to the porosity and metallurgical bond

    摘要噴射沉積多孔鋁合金板坯由於有孔洞且缺乏良好的冶金結合，直接軋制時易出現板坯表面裂紋及邊裂。
  10. The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved

    本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。
  11. So the effecte of frame - pack rolling technology on microstructure and mechanical proprties of spray deposited porous 5a06 and 8009 aluminum alloy sheets after rolling were studied

    為此研究了外框限制軋制工藝對噴射沉積多孔材料5a06和8009鋁合金板坯軋制組織和力學性能的影響。
  12. The paper put forward a new model and tendency of rolling plate which adopt the medium thickness casting billet and the modern steckel mill

    進而指出，中等厚度的連鑄坯與現代爐卷軋機組合的成卷軋制中厚板的生產模式，是今後中厚板生產發展的一種新模式和方向。
  13. Analysis of quality control system of thin slab continuous casting and continuous rolling line of tangshan iron and steel co., ltd

    唐鋼薄板坯連鑄連軋生產線質量控制系統分析
分享友人
分享到 Line

分享到臉書