軋制過程 的英文怎麼說

中文拼音 [yàzhìguòchéng]
軋制過程 英文
operation of rolling
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 過程 : process; procedure; transversion; plication; course
  1. In this thesis, according to changeable quantity, nonlinear and time - varying of the copperplate rolling process, the simple fuzzy controller was first designed based on the analysis of the fuzzy control theory, which is the basis of other high - level controllers

    本文針對銅板軋制過程具有多變量、非線性、時變性的特點，在分析了模糊控制基本理論的基礎上，首先設計了銅板軋制簡單模糊控制器，這也是進一步設計其它高性能模糊控制器的基礎。
  2. The results show that " the frame - pack rolling " technology can increase the densify, avoid cracking during rolling, and effectively improve the deformability and mechanical properties of the spray deposited porous aluminum alloy sheets

    結果表明：外框限制軋制工藝提高了噴射沉積多孔材料的緻密度，避免了軋制過程中裂紋的形成，有效地改善了噴射沉積板坯的軋制性能及材料的力學性能。
  3. Microstructure evolution of twin lamellae with different lamellar size in rolling deformation at room temperature

    孿晶片層結構在室溫軋制過程中的微觀結構演變
  4. Visual simulation of cold rolling process based on opengl

    的冷軋軋制過程可視化模擬
  5. The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

    利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。
  6. After an actual rolling process of 2050 mill was simulated by using the model, evolution laws of strain field, temperature field and microstructure were analyzed

    運用該模型對2050現場實際軋制過程進行模擬計算，分析了軋制過程軋件變形場、溫度場及顯微組織的演變規律。
  7. The research of the influence of gap setting precision on finishing plate size precision shows that the sensibility of finishing size precision to gap setting precision of the first several passes is low

    摘要分析中厚板軋制過程不同道次輥縫設定精度對軋件終軋尺寸精度的影響，證明了軋件終軋尺寸精度對前面道次的輥縫設定精度不敏感。
  8. Influence of process factors on roll crown during aluminum strip rolling process

    工藝因素對鋁帶材軋制過程中輥型的影響及控制
  9. This method can decrease the gap setting time for which the oil column of hydraulic cylinder is not retracted and there is no minute adjustment of oil column for the first several passes

    採用該方法，軋制過程液壓缸油柱不用回縮，而且前面道次液壓不進行微調，從而節省了輥縫設定時間。
  10. The result of simulation the model and parameters are correct. it ensure the whole p ' roject being finished successfully

    這也為整個冷連軋機軋制過程動態模擬項目的順利完成提供了保證。
  11. The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product

    摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。
  12. Hydraulic servo system used in coiler is mainly to realize the step - by - step control. by using the servo system, vibration and striking are largely decreased, the accidents are reduced, and the level of automation is largely improved, as well as the quality of production

    電液伺服系統在現代的熱軋卷取機中的應用主要是實現帶頭的自動步進迴避，這樣就有效地消除沖擊，同時也使卷取過程中各種事故大為減少，大大提高了軋制過程的自動化水平，產品產量和質量。
  13. Abstract : as the most critical factor of mpm process, the groove design of fewer stand mandrel retained mpm significantly affects the rolling course as well as product quality

    文摘:少機架限動芯棒連軋管機孔型設計是連軋管工藝的核心，對軋制過程的建立和產品質量起著極其重要的作用。
  14. Computer simulation for rolling processes of bar, wire and shape steel

    型材軋制過程的計算機模擬模擬
  15. Three - dimensional dynamic numerical simulation of ring rolling process

    環件軋制過程三維動態數值模擬
  16. Sensitivity analysis for rolling process based on support vector machine

    基於支持向量機的軋制過程靈敏度分析
  17. In the absence of heat, i think, no oxide coating is forme during rolling

    在無加熱的條件下，我想，軋制過程中不會生成鱗皮吧
  18. In the absence of heat, i think, no oxide coating should form during rolling

    在無加熱的條件下，我想，軋制過程中不會生成鱗皮吧！
  19. In this paper, the internal transverse cracks of continuous casting slabs of a niobium - bearing peritectic grade of steel are investigated using electron probe microanalyser and optical microscope

    摘要連鑄坯厚度中心存在的內裂紋在後續的軋制過程中軋不合而對產品的質量帶來重大的影響。
  20. Based on shanghai bao steel co. practical project, which is modeling 、 simulating of dynamic rolling procedure and control optimizing for cold continuing roll mill, the research of control optimization on the dc motor speed control system is studied

    本課題結合上海寶鋼集團公司「冷連軋機軋制過程動態模擬及控制優化」項目，對直流電機速度控制進行控制優化研究。
分享友人
分享到 Line

分享到臉書