軋槽速度的英文怎麼說

中文拼音 [cáo]
軋槽速度英文
pass line speed

  • : 軋動詞[方言]1 (擠) press hard against each other; push against2 (結交) associate with; make f...
  • : 名詞1 (盛牲口飼料或飲料等液體的器具) trough; manger (for water animal feed wine vat) 2 (兩邊...
  • : Ⅰ形容詞(迅速; 快) fast; rapid; quick; speedy Ⅱ名詞1 (速度) speed; velocity 2 (姓氏) a surna...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • 速度: 1. [物理學] velocity; speed; blast; bat 2. [音樂] tempo3. (快慢的程度) speed; rate; pace; tempo

※中文詞彙軋槽速度在字典百科國語字典中的解釋。

  1. Abstract : the shaping equation of steamed bread in circular trough camber of shaping roller, the instantaneous velocity of its surface, and the strength by shaping roller were analyzed during shaping, then a theory base for the design of steamed bread shaping machine was provided

    文摘:分析了饅頭成型過程中成型輥上圓弧曲面內饅頭生坯的運動方程,饅頭表面動點瞬時及饅頭成型時受力分析,為饅頭成型機的設計提供了理論依據。
  2. Numerical simulation signal and vibration acceleration signal of a roughing mill main drive speed reduction unit have been decomposed by using empirical mode decomposition algorithm ; each component has been carried on spectral analysis

    摘要運用經驗模式分解演算法對數值模擬信號及某鋼廠粗機主傳動減機振動加信號進行了分解,從而得到若干個基本模式分量,對每個模式分量進行了頻譜分析。
  3. Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase

    研究結果表明,減薄鑄板坯厚可提高鑄;隨著鑄降低、鑄區增大與鑄坯厚減薄,制壓力峰值增大;隨著鑄輥徑增大,制壓力增大,因此鑄機力能設計參數也要相應增大。
  4. The varieties of interior parameter and exterior load disturbance and the presence of saturation nonlinear have great influence on the dynamic process and tracking effect of the system, so there are practical meanings and theory values to apply robust control methods to speed system. the development and status quo of robust control theory is summarized

    由於系統內部參數的變化、飽和非線性的存在及外界負載擾動的變化對系統的動態過程及跟蹤效果有較大的影響,因此,本文應用魯棒控制方法對系統進行控制研究,具有較大的實際意義和理論價值。
  5. When work rolls become worn the roughness is diminishing creating slippage in the roll bite at higher speeds

    工作輥磨損后,粗糙遞減導致在較高下進料(咬入帶卷)時產生滑移。
分享友人