軋輥部件 的英文怎麼說

中文拼音 [yàgǔnbùjiàn]
軋輥部件 英文
roll assembly
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 部件 : component; unit; parts; assembly; subsystem; secundina （pl. secundinae）
  1. Abstract : by utlizing abundant local resource of ytirium and combining the characteristics of magnesium, barium, calcium and silicon, a sort of composite nodulizer - ytirium - based heavy rare earth nodulizer was developed which is characterized by its good desulphurizing and deoxidizing rate effect, excellent effect to neutralize anti - nodulizing effect of trace elements, strong nodulizng effect and degeneration - resistance, good effect to fine matrix structure, decreased chilling tendency and wide scope of applicatiom using this nodulizer to produce some important castings such as water - cooled wall of blast furnace and roller could increase mechanical properties of central area and casting yield

    文摘:利用江西省豐富的釔基重稀土，結合鎂、鋇、硅、鈣等元素的特性開發了釔基重稀土復合球化劑，該球化劑具有脫硫、脫氧、抗干擾元素、球化和抗球化衰退能力強，細化基體組織，白口傾向小，適用范圍寬等特點，應用於高爐冷卻壁，軋輥等關鍵鑄件上可提高心部力學性能和工藝出品率。
  2. It is indicated that three - roll cross wedge rolling process has a distinct advantage in the forming quality of the center of rolled pieces

    分析表明，三輥楔橫軋軋制工藝在軋件心部成形質量上具有明顯的優勢。
  3. The occurrence probability and existence form of internal defects in rolled pieces during three - roll and two - roll cross wedge rolling were compared and analyzed by finite element numerical simulation

    摘要採用有限元數值模擬方法，比較分析了三輥楔橫軋與兩輥楔橫軋軋件內部缺陷的產生幾率和存在形式。
  4. The reason that the internal defects little occur at the center points and fissure takes an annular form during three - roll rolling was expounded based on the state of stress and strain at the center of rolled pieces

    根據軋件內部的應力應變狀態，闡述了三輥軋制軋件中心點缺陷產生可能性較小和斷裂呈環向裂紋的原因。
  5. Upon analysis of advantages and disadvantages of varieties of support structure of roller of cross wedge rolling mill in existence, a new type of support for the upper roller has been introduced with calculation in design of certain components combined with a specific type of such machine

    摘要通過分析現有輥式楔橫軋機上軋輥各種支撐結構的優缺點，重點介紹了一種新型的上軋輥支撐結構並結合具體型號楔橫軋機對其部分部件進行了設計計算。
  6. Bottom roll assembly

    下軋輥組合部件
分享友人
分享到 Line

分享到臉書