軋薄輥 的英文怎麼說
中文拼音 [yàbógǔn]
軋薄輥
英文
reduction roll-
Rolling - cutting biscuit shaping machine is new equipment of making soda biscuit, good toughness of thin biscuit and super - thin biscuit. it ' s high production efficiency, low noises, safe operation, convenient, beautiful outer shape. this machine can press and roll rough flour 3 times and equiped with remaining flour recycling machine, also equiped with double - rolling cutting shaped equipement, in the mean time, it can produce two biscuit embryo of differnt shape. 3 times pressing - rolling machine can adjust different thickness and biscuit rough surface. it can roll rough flour and do not stick to rough flour embryo, correctness rate of adopting mould to cut margin of flour embryo reaches 100 percent so that avoid deforming of embryo due to deviation. this machine is one equipment which adopting advanced and won first technical rewarding for its independently control operation, beautiful outer appearance
滾切式餅干成型機是連續製作梳打餅、韌性和薄餅超薄餅的新型設備，具有生產效率高、噪音低，操作安全、方便，外型美觀等優點，本機具有三道軋輥制皮和余料回收機，配備雙滾切成型裝置，同時能生產兩種不同形狀的餅干胚不停機，三道軋輥能同時調節不同厚度和餅皮具有軋輥不粘皮、採用印模切邊一次同步進行準確率100 % ，避免偏差而造成餅胚變形，該機具有獨立控制操作，外形美觀，是目前國內較先進而獲得技術一等獎的設備。Fictious simulation of high - speed roll casting has been carried out on the basis of the fact. the results showed that roll casting speed increase with the decrease of the thickness of the strip, and the peak value of rolling pressure decrease with the increase of roll casting speed and thickness of strip or the increase of roll casting zone. the designed parameters of mechanical capabilities of the roll caster should be raised when rolling pressure increase with roller diameter increase
研究結果表明，減薄鑄軋板坯厚度可提高鑄軋速度；隨著鑄軋速度降低、鑄軋區增大與鑄軋坯厚度減薄，軋制壓力峰值增大；隨著鑄軋輥徑增大，軋制壓力增大，因此鑄軋機力能設計參數也要相應增大。Responding to the call of industrial policy adjustment in our country, yaoyu special steel company has started replacing hot - rolling with cold - rolling in the production of electric steel since 2003. it entrusted xinye gaoke group to make design and build the production line of cold - rolled electric steel with annual output of 200 thousand tons. after three years of construction, it has achieved the successful trial production of 20 - roll mill and continuous annealing and coating machine imported from germany
耀宇特鋼從2003年開始，響應國家產業政策調整的號召，開始電工鋼以冷代熱技改工程，委託新冶高科集團原冶金部鋼研院設計，進行年產20萬噸冷軋電工鋼生產線的建設，經過近三年的建設，目前從德國引進的20輥軋機及連續退火塗層機組均已試產成功，為提高產品的性能和質量，同時提升我國電工用薄鋼板的生產作出了卓越的貢獻。The configuration of conventional backup and work rolls for revamped 1700 tandem cold rolling mill at wisco was proved unreasonable by systematical test as the cause of work roll edges contact during thin strip rolling and unsatisfactory flatness of product
摘要通過現場跟蹤測試和生產實踐發現武鋼1700冷連軋機組「酸軋聯機」改造工程中存在常規凸度輥形配置方案不合理，由此引起了薄規格軋制的工作輥「壓肩」現象和軋制過程欠穩定導致成品板形質量欠佳等問題。Experimental research into annealing schedule for twin - roll casting strip of high - speed steel
雙輥鑄軋高速鋼薄帶退火制度的實驗研究1 a set of 20 - rool mill with four vertical posts wv20seh55 - 300 1150 introduced from german sundwig. the mill may yearly produce 80, 000 tons of various markings of cold - rolled stainless steel, silicon steel, and carbon steel sheets with 0. 1 mm in thickness and 0. 01 in tolerance
1德國引進森德威wv20seh55 - 3001150四立柱式廿輥軋機一臺套，年產量8萬噸，該設備可生產成品最薄厚度至0 . 1mm的各種牌號的冷軋不銹鋼硅鋼普碳鋼板，公差可達到0 . 01mm 。Phosphorus segregation and effect on mechanical properties of twin roll strip cast high p and cu steels
雙輥鑄軋高磷銅鋼薄帶的偏析行為及對力學性能的影響The application of vcr improves shape control, giving better strip flatness, higher capacity for thin strip and better self maintenance of roll contours
現場應用表明：改善了軋機板形調控性能，提高了帶鋼板形質量，增強了薄規格品種軋制能力，支承輥輥形自保持性較好。R amp; amp; d of thin - gauge high - speed twin roll continuous cast - rolling technology for aluminium alloy strip
雙輥快速連續鑄軋超薄帶坯技術進展The twin roll casted austenite stainless steel strip was cold rolled, and the surface quality and the microstructure of the strip was investigated
摘要對雙輥鑄軋704不銹鋼薄帶進行了冷軋處理，分析了冷軋前後薄帶的表面質量及顯微組織。The investigations on withstanding thermal damages for roll shell in the metal thin strips produced with continuous roll casting
金屬薄帶鑄軋輥套抗熱損傷行為分析分享友人