軋輥的作用力 的英文怎麼說

中文拼音 [yàgǔndezuòyònglì]
軋輥的作用力 英文
roll force
  • 軋 : 軋動詞[方言]1 （擠） press hard against each other; push against2 （結交） associate with; make f...
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 的 : 4次方是 The fourth power of 2 is direction
  • 用 : Ⅰ動詞1 （使用） use; employ; apply 2 （多用於否定: 需要） need 3 （敬辭: 吃; 喝） eat; drink Ⅱ名...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 用力 : exert oneself; put forth one's strength
  1. Through the simulation of the forming process, we can get the deformations, stress, strain, plastic flowing in sheets and the interface state under impact load and rolling load, the deformation of the sawtooth form and comparing to the initial state, the results above are expressed in computer animated way. and the effect of geometrical ( mainly different form, including 90 degree, isoceles triangle ， 75 degree, and 1. 5 high and wide ), material and technical parameters on the bond strength are analyzed, also including the comparison of different sawtooth form. the optimum parameters are got

    對雙金屬復合板成型過程進行模擬，從而得到在沖擊載荷和軋輥壓力作用下基板和覆板的應力、應變分佈和塑性流動變形規律，復合后的齒形的變形情況與初始齒形形成對比，以動畫的方式模擬成型過程，並分析了不同幾何參數（主要是不同的齒型，其中包括直角齒型、等腰齒型、 75度齒型、 1 . 5高寬齒型） 、材料參數、工藝參數對復合強度的影響，以及不同齒型的變形對比以及齒型對復合情況的影響，提出最優齒型、最優工藝參數，有效地指導了實驗。
  2. Theoretically the varying contact rolling technology can increase the transverse stiffness of loaded roll gap, heighten the control effect of roll bending, improve the distribution of contact force between backup roll and work roll

    從理論上分析了變接觸軋制技術在提高承載輥縫橫向剛度、增加彎輥力調控功效、改善輥間接觸壓力分佈方面的作用。
  3. Works on the bending roll system of four - roll rolling mill, the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys, the maximum deformation of the work roll was calculated, and the curve of the gap adopting the least - squares method was fitted, which set the base of the further calculation of load - gap shape

    摘要以四輥軋機的彎輥系統為研究對象，利用有限元分析軟體ansys研究彎輥力和輥間接觸應力引起工作輥形狀的變化，計算工作輥彎曲的最大變形量，並用最小二乘法對輥縫曲線進行擬合，為進一步計算有載輥縫形狀提供可靠的理論依據。
  4. There are five parameters need to be measured. there are five channels for input : the displacement of casting - roller, the rotate speed of casting - roller, the pressure of casting and rolling, the casting temperature and the water - speed of cooling water. they are measured by raster, photoelectric coder, strain pressure sensor, thermocouple and turboflowmeter

    系統需要進行監測的參數有五個，即有五路輸入信號：鑄輥位移、鑄輥轉速、鑄軋壓力、澆鑄溫度、冷卻水流速，分別採用光柵、光電編碼器、應變式壓力傳感器、熱電偶和渦輪流量計作為檢測元件。
  5. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥表面淬硬層與其心部金屬材料組織性能的差別，採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬，並將模擬結果與傳統強度校核方法進行了對比分析，研究了軋輥淬硬層厚度對輥間接觸應力的影響規律。
  6. Compares with the same centripetal ball bearing, has the big radial direction load bearing capacity, mainly is suitable for the cold hot - rolling mill, working roll support rolls and so on cogging mill

    與相同的向心球軸承相比，有較大的徑向負荷承載能力，主要適用於冷熱軋機，開坯機等工作輥支承輥。
  7. The ability of shape control could be improved by the application of wrs rolls as the downstream stands in the design and renovation of hot strip rolling

    摘要在熱帶鋼連軋機設計及改造中採用wrs輥系作為下游機座可以增強機組的板形調控能力。
  8. The feed material is broken between the counter - rotating rolls and crushed by pressure and shearing stress

    在壓力和切力的作用下，給料在彼此相向旋轉的軋輥間破碎。
  9. And its nnc and nni are both established with the optimal neural network. so the hydraulic bend roller system ' s dynamic response velocity and static tracking precision are advanced. hydraulic bend roller force can operate better and mill ' s dynamic characteristic is improved

    將優化網路用於液壓彎輥系統的控制中，採用內模控制方案，辨識器和控制器用優化網路來離線設計、在線調整，提高了液壓彎輥系統的動態響應速度和穩態跟蹤精度，充分發揮了液壓彎輥力對板形的調整作用，改善了軋機系統的動態特性。
分享友人
分享到 Line

分享到臉書