軸向壓力 的英文怎麼說

中文拼音 [zhóuxiàngyālì]
軸向壓力 英文
axial compre ion
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. Mas precursor powders were uniaxially pressed at 100 mpa employing a lubricated steel cylindrical mold. after sintering at 1450 for 2 hours, single - phase cordierite ceramic is prepared, and its relative density is 95. 1 %

    Mas先驅體粉末在100mpa的軸向壓力下成型后，經1450無壓燒結2小時，得到單相堇青石陶瓷，其緻密度達95 . 1 。
  2. The dishing ring seals belong the end face sealing parts, and act as sealing by some axial compression. because of different distribution of internal pressure and temperature, the friction inside the end - face is also different at all area

    碟形密封圈屬于端面密封元件，依靠一定的軸向壓縮量進行密封，由於端面內壓力分佈、溫度分佈不均，端面內的摩擦狀況也不是處處相同。
  3. The plating in ships is generally subjected to combined in - plane and lateral pressure loads. in - plane loads include biaxial compression / tension and in - plane bending and edge shear, which are mainly induced by overall hull girder bending and / or torsion of the vessel. lateral pressure loads are due to water pressure and cargo

    面內載荷分為軸向壓應力或拉應力、邊緣剪切應力以及面內軸向彎曲應力。實際的船舶結構中面內載荷通常由船體梁的總縱彎曲或者船體梁的扭轉引起。側向壓應力則由水壓力和貨物壓力引起。
  4. This article gives the subsistent ability and the analysis result of intensity after repair in the open field airplane composite material structure by research the intensity, rigid and repair problem under a axis compress loads on a typical three stiffened composite laminate which has a penetrability crack ( a scatter damage ) by a shrapnel

    本文通過飛機典型復合材料三加筋層壓板結構在被彈片劃開一穿透性切口（離散源損傷）后，在軸向壓縮載荷作用下所產生的強度、剛度以及修理問題展開了技術研究及探討，給出軍機復合材料加筋板在彈擊後生存力以及外場修理后強度恢復分析結果。
  5. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  6. Thermoplastics piping systems. non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings. test method for leakightness under internal hydrostatic pressure without end thrust

    熱塑料管道系統.壓力管和模塑配件的合成橡膠密封環型接合.在無軸向推力時內部流體靜力學壓力下密封性試驗方法
  7. A two component design consisting of appropriate size and length of structural reinforcing rods and dead - end component is required to transfer axial tensile loads and distribute radial compressive forces through the plastic jacket and onto the internal strength members without damaging the fragile plastic jacket or internal optical fibers

    螺旋預絞絲結構不僅能有效地降低配合區域內光纜單位應力和避免應力集中，傳遞軸向張力，而且將預絞絲的徑向壓力均勻地分佈在這段較長的配合區域內。
  8. Based on the classical nonlinear plate theory, axisymmetric post - buckling behavior of a functionally graded circular plate under radial compression was investigated

    摘要基於經典非線性板理論，研究了功能梯度圓板在均勻的徑向壓力作用下的軸對稱過屈曲問題。
  9. During the ship collision and grounding, the crushing collapse of thin - walled structure subjected to compressive load is one of the important failure modes

    摘要在船舶碰撞和擱淺中，薄壁結構在軸向壓力條件下的壓潰破壞是一種重要的破壞模式。
  10. Through the fem calculation and the analyzing data of the field, the result is that the central wall mainly endures the vertical pressure from the structure transferring and its bending moment is relatively less and its position of the maximum value of the bending moment locates in the joint between the central wall and the steel framework

    通過有限元計算和對現場監控量測數據的分析，論文得出：中隔墻主要承受結構傳遞的豎向壓力，彎矩值較小；鋼拱架的軸力以受壓為主，彎矩值在中隔墻上方位置處最大。
  11. The stress and working pressure on teeth of the staged nut in screw presses has been studied by fem method which proves that using staged nut in screw presses is helpful for improving the non - uniform distribution of stress and working pressure on the teeth and extending the working life of the screw

    摘要採用了有限元法對滑動螺旋壓力機的階梯式螺母進行了受力分析，研究了螺母螺牙應力及螺牙工作面的接觸壓力，並將階梯式螺母與普通螺母進行對比，認為螺旋壓力機中使用階梯式螺母有利於改善螺牙牙根應力軸向應力分佈不均和螺牙工作面的接觸壓力分佈不均的情況，從而提高螺旋工作壽命。
  12. This can be of significant benefit to cut down the cost and time limit for a project the program package gone with this paper may realizes the dynamic simulation for all of courses in hoisting, and may synchronously displays the axis force of derrick, the pull - force of the steel wire, obliquity of equipment and overloading instance

    這有利於工程實踐中方案變更、施工現場條件復雜多變等的方案驗算，節約成本和縮短工期。本論文程序為桅桿吊裝整個過程實現了動態模擬，顯示桅桿軸向壓力、鋼絲繩拉力、設備傾角和起重超載提示，為安全吊裝設備提供重要的數據，有利於作業過程的全程監控。
  13. Lastly, the author investigated the impact of the axial pressure gradient on three - dimensional chaotic mixing in eham by computing the mixing efficiency of a tracer

    最後，通過計算三維eham混沌混合中代表性流體質點的拉伸效率行為，確定軸向壓力梯度的影響。
  14. Analysis of the ultimate loading capacity of tubular tt - joints under axial compression

    管節點在軸向壓力下的極限載荷分析
  15. Pressure gauge with back connection

    軸向壓力表
  16. ( 2 ) the numerical result and the critical value ' s effect imposed by circumferential initial stress numerical character on cylindrical thin shell beard the press at axis

    （ 2 ）給出了周向初應力數值特徵對軸向壓力圓柱薄殼臨界值的影響，給出數值結果。
  17. Axial compressive force

    軸向壓力
  18. Axial compressive load

    軸向壓力載荷
  19. Axial pressure load

    軸向壓力負載
  20. Fibre optic interconnecting devices and passive components. basic test and measurement procedures. part 2 - 11 : tests. axial compression

    光纖互連裝置和無源元件.基本試驗和測量程序.第2 - 11部分:試驗.軸向壓力
分享友人
分享到 Line

分享到臉書