軸向拉伸力 的英文怎麼說

中文拼音 [zhóuxiàngshēn]
軸向拉伸力 英文
axial tensile force
  • : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
  • : 拉構詞成分。
  • : Ⅰ動詞(展開) stretch; extend Ⅱ名詞(姓氏) a surname
  • : Ⅰ名1 (力量; 能力) power; strength; ability; capacity 2 [物理學] (改變物體運動狀態的作用) forc...
  1. The condition of uniaxial stress is closely approximated in prismatic bars subjected to pure axial tensile.

    的應狀態跟稜柱桿承受單純十分近似。
  2. The structure of the deformation bands was observed and photographed by a microscope with a camera accessory. a user material mechanical behavior ( umat ) subroutine was developed based on the crystal plasticity model, and with it, the anisotropic elasto - viscoplastic behavior in single crystals was described. slip systems " evolution was simulated by using finite element method with the subroutine

    本文使用數值模擬的方法對[ 001 ] 、 [ 011 ] 、 [ 111 ]以及偏加載的多種取試樣進行了試驗模擬和循環模擬,研究了不同取的試樣在加載過程中滑移系的演化情況,並對試樣的宏觀學行為和細觀機理進行了評述。
  3. Non - linear finite element analysis of rubber layer bonded between two rigid spheres has been performed for rubber ’ s characteristic of large deflection and nearly incompressibility. the relationships between stiffness and deformation have been gained when large tensile deformations are imposed. the effects of different poisson ’ s ratios of rubber matericals on the stiffness and stresses of rubber layer have

    針對橡膠的大變形及接近不可壓縮的特點,對工程中常用的橡膠-剛球支座進行非線性有限元分析,了解了支座的剛度和應的變化情況以及泊松比對兩者的影響,得出的支座受時的剛度與變形關系。
  4. Axial tensile stress

  5. Metallic materials - verification of static uniaxial testing machines - tension creep testing machines - verification of the applied load

    金屬材料.靜態單試驗機的校正.蠕變試驗機.對作用負載的校驗
  6. The studies on the influence of stretching process on the appearance and mechanical performances of camp fibers showed, that orientation of the molecular along the axis of the fiber was improved after stretching in the steam bath, and the mechanical performance were also improved

    研究了工藝對camp纖維形貌及學性能的影響。結果表明, camp纖維在蒸氣浴中進行高倍后,大分子沿纖維程度提高,纖維的學性能得到改善。
  7. Metallic materials - verification of static uniaxial testing machines - part 1 : tension compression testing machines - verification and calibration of the force measuring system

    金屬材料.靜態單試驗機的驗證.第1部分:壓縮試驗機.測量系統的驗證和校正
  8. Axial tensile force

    軸向拉伸力
  9. Corrosion of metals and alloys - stress corrosion testing - preparation and use of uniaxially loaded tension specimens

    金屬和合金的腐蝕.應腐蝕試驗.第4部分:載荷試樣的制備和使用
  10. Lastly, the author investigated the impact of the axial pressure gradient on three - dimensional chaotic mixing in eham by computing the mixing efficiency of a tracer

    最後,通過計算三維eham混沌混合中代表性流體質點的效率行為,確定梯度的影響。
  11. Metallic materials - verification of static uniaxial testing machines - tension compression testing machines - verification and calibration of the force - measuring system

    金屬材料.靜態單試驗機的鑒定.和壓縮試驗機.測系統的鑒定和校準
  12. Standard practice for verification of test frame and specimen alignment under tensile and compressive axial force application

    和壓縮作用下驗證試驗框架和樣品準直精度的標準實施規程
分享友人