軸安裝誤差 的英文怎麼說

中文拼音 [zhóuānzhuāngwùchā]
軸安裝誤差 英文
axle misalignment
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 誤差 : error
  1. The model of influence upon the parallel between servo optic axis from the angle error of installation plans presented. whereby the theoretic analysis is carried out and the analyzing results are obtained. the method of obtaining the angle error through measuring the installation plans with three - coordinates measuring device and fitting the measurement data is put forward and pave a road for lessening the influence

    對安裝面角誤差影響隨動光軸平行性的問題也建立了數學模型，以此為出發點進行理論分析，給出了分析結果；提出用三坐標測量機測量安裝面，通過擬合得到安裝面的角誤差；從而為減小這一誤差源對隨動光軸平行性的影響鋪平了道路。
  2. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  3. The outside diameter of the self - contained bearing is spherical to match corresponding spherical inside diameter of the housing providing self - aligning between these two members, which compensates for misalignments of the units resulted from errors in mounting and distorting of the foundation

    軸承的外徑與軸承座內徑為球面配合，兩者之間具有自動調心功能，可補償因安裝誤差產生的軸線不重合及安裝底面的變形。
  4. First, the basic theory of static load sharing mechanism has been presented, mainly including manufacturing and assembly error of each gear component ' s axis and each bearing ' s axis, gear size ( tooth thickness ) errors, simultaneous error of middle two - tooth. the formula of equivalent mesh error has been deduced, the load sharing coefficient has been computed. second, the influences of each error on the static load sharing coefficient have been discussed

    首先，從靜力學的角度研究了星型齒輪系統均載的基本原理；確定了影響齒輪系統均載特性的製造和安裝誤差，主要包括：各個齒輪構件的中心軸線製造和安裝誤差、軸承中心軸線的製造和安裝誤差、齒厚偏差、雙聯星輪同時嚙合線誤差；推導了這些誤差的當量嚙合誤差的計算公式，分析了系統的均載特性。
  5. After considering the coupling of the mounting errors and elastic deformation, the meshing influences of the error of the center distance, the setting parametric error in the axial direction, and the intersect angle between the two axes on transmission performance are investigated. 4

    考慮到安裝誤差和載荷作用下的彈性變形等非共軛因素耦合作用，分析了漸開線蝸桿傳動在安裝時存在中心距誤差，軸間相對位置誤差，軸間相對夾角誤差對其承載嚙合的影響； 4
  6. On the basis of kinematic analysis of the tripod universal joint, this paper analyses the motion errors of this system, which related to the manufacturing error, installation error, bearing clearance, and so on

    摘要在三叉桿式萬向聯軸器的運動分析的基礎上，充分考慮到機構製造和安裝的不精確性，運動副軸承的間隙，作用於連桿上力及溫度變化引起的連桿變形等因素，進行了三叉桿式萬向聯軸器運動誤差分析。
  7. Secondly, the beam orbit offset effects caused by the initial beam offset and the linac components " offsets have been quantitatively studied first. as an example with the injector linac for beijing electron positron collider upgrading project ( bepcii ), the beam orbit offset caused by the above error effects have been simulated and analyzed

    其次定量研究束流的初始徑向誤差和加速器部件的安裝誤差等對束流軌道偏軸的影響，並以北京正負電子對撞機二期工程（ bepc ）的直線加速器為例，給出了上述各種誤差導致軌道偏軸的模擬計算結果及其分析。
分享友人
分享到 Line

分享到臉書