軸承油槽 的英文怎麼說
中文拼音 [zhóuchéngyóucáo]
軸承油槽
英文
bearing groove- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 承 : Ⅰ動詞1 (托著; 接著) bear; hold; carry 2 (承擔) undertake; contract (to do a job) 3 (客套話...
- 油 : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
- 槽 : 名詞1 (盛牲口飼料或飲料等液體的器具) trough; manger (for water animal feed wine vat) 2 (兩邊...
- 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
- 油槽 : channel for oiling
-
Plain bearings - lubrication holes, grooves and pockets - dimensions, types, designation and their application to bearing bushes
滑動軸承.潤滑油孔油槽和油穴.尺寸類型標記及其對軸套的應用Usually, the outer ring of the tl bearings has grease groove, bearings having no grease groove are to be provided, too
外球面球軸承外圈一般帶油槽,也生產外圈無油槽的產品。Usually, the outer ring of the yc bearings has grease groove, bearings having no grease groove are to be provided, too
Yc外球面球軸承外圈一般帶油槽,也生產外圈無油槽的產品。There is one oil groove in the bronze bushing, where lubricant can flow into the axis from the oil hole on the cap of housings
軸瓦內表面的不承擔載荷部分開有油槽,潤滑油通過進油孔和郵溝流進間隙。Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward
摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析,研究其運行不穩定的原因,提出改造措施,包括滑動軸承潤滑油槽,齒輪泵的機械密封,降低齒輪泵出口壓力,改自動提速為手動提速等等。For pump shafts, the results reveal that the stress in the spline is higher than the other parts of the shaft, and the highest stress is at bottom and terminal of the spline. in fact, the broken of shafts is at the same position ; it demonstrates that the calculation is right
實踐證明,軸斷部位基本集中在潛油泵軸花鍵的根部,說明計算結果和實際是吻合的;對于潛油電機軸,應力集中點主要處在軸承鍵與環槽的交界處和花鍵的根部。Plain bearings ; hydrostatic plain journal bearings under steady - state conditions ; characteristic values for the calculation of oil - lubricated plain bearings with drainage grooves
滑動軸承.穩定工作條件下靜壓向心滑動軸承.帶排油槽Plain bearings - wrapped bushes - lubrication holes, lubrication grooves and lubrication indentations
滑動軸承.卷制軸套.潤滑油孔油槽和油穴Plain bearings - wrapped bushes - part 3 : lubrication holes, lubrication grooves and lubrication indentations
滑動軸承卷制軸套第3部分:潤滑油孔潤滑油槽和潤滑油穴Plain bearings - wrapped bushes - part 3 : lubrication holes, lubrication grooves and lubrication indentations iso 3547 - 3 : 1999
滑動軸承.卷制軸套.第3部分:潤滑油孔油槽和油穴分享友人