軸承體 的英文怎麼說

中文拼音 [zhóuchéngtǐ]
軸承體 英文
bearing body
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 體 : 體構詞成分。
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Conventional aerostatic bearings have the problems of vibrations and motion inaccuracy due to the low stiffness

    傳統的靜壓氣體徑向軸承由於低剛度而存在著振動和運動精度不高的問題。
  2. By studying and analyzing load - bearing mechanism of multi - support structure, the paper summarized out measures that was used to improve aerostatic motorized spindle load - bearing characteristics

    研究分析多支承結構的承載機理，總結出提高氣體靜壓電主軸承載特性的措施。
  3. Then this thesis apply iterative computation using fluent software, that means fluent is successfully used in the research of porous aerostatic bearing field for the first time

    然後用計算流體力學中的fluent軟體進行迭代計算，成功地將其引入到多孔質靜壓軸承研究領域。
  4. People now pay much attention at porous aerostatic bearing which has obviously higher load capacity and better damping characteristic and stability. there are two kinds of porous aerostatic bearing : the whole porous and partial porous

    多孔質氣體靜壓軸承能明顯提高軸承的承載能力，具有更優越的阻尼特性和穩定性，故得到廣泛的關注。
  5. Design and analysis on high speed static air bearing test - bed

    高速徑向氣體靜態軸承試驗臺的設計與分析
  6. Amb and foil air bearing has its inherent shortages when it is used alone

    磁軸承和箔片氣體軸承都有本身固有的不足，單獨使用都存在一些問題。
  7. Air bearing has a lot of absolute advantages when it is used in high speed bearing, low friction and low wastage, high precision bearing and special conditions

    氣體軸承在高速支承，低摩擦、低功耗支承，高精密支承和特殊工況下的支承等領域內有絕對的應用優勢。
  8. Now we unite amb with air bearing ( amb - ab ) to overcome their shortages. it is a new technology in bearing field, it will more superior than amb and air bearing

    將兩者結合在一起，利用它們各自的優點並克服對方的缺點，將是軸承領域的新技術，其性能要遠比磁軸承或箔片氣體軸承的性能優越。
  9. Many international experts have done research in amb - ab, but the air bearing occupying a long axis space. the rotor ' s dynamics performance is depressed. a new type amb - ab was brought forward in this paper, the film air bearing was integration in amb

    本文研究了一種新型的磁氣混合軸承結構，其特點是將箔片氣體軸承集成在磁軸承的氣隙裏面，不佔據軸向空間，因此與國外的研究有本質的區別。
  10. Airframe rolling bearings - technical specification

    飛行器機體滾動軸承.技術規范
  11. Aerospace series. airframe rolling bearings. technical specification

    航空航天系列.機體用滾動軸承.技術規范
  12. Xm ) trundle needle, trundleing the post thrust bearing trundles the needle through the roll part of the body, cylinder roller and thrust maintain shelf and the thrust bed down the livestock to make up, trundleing needle and the cylinder roller is subjected to the shelf maintaining that the thrust maintains and guides. moreover thrust bed down the livestock against the difference, shaft, the pedestal encircles and employs in company, fix module shaft shoulder end face and the shell opening back plane dimensional tolerance, geometry accuracy, rigidity, axial is moved up and down, coarse degree ought to accord with the internation ， national standard stipulation demand

    滾針，滾柱推力軸承由滾動體滾針，圓柱滾子及推力保持架和推力墊圈組成，滾針和圓柱滾子受到推力保持的保持架引導，並與不同的推力墊圈，軸，座圈一起使用，安裝組件的軸肩端面和外殼孔底面的尺寸公差，幾何精度，剛性，軸向跳動，粗糙度應符合國際，國家標準規定的要求。
  13. The main bearing journals fit into the cylinder block and the big end journals align with the connecting rods

    主要軸承曲頸安裝在氣缸體和與連桿大頭末端匹配的曲頸上。
  14. As to the high speed of electric spindle system, the angle - contact bearings are usually applied to supporting the shafts. because the supporting stiffness of rolling bearing is non - linear, especially under the circumstances of high speed and ultrahigh speed, the internal working status is so complicated that it is not regarded as routine linear support and ordinary non - linear support. centrifugal effect of the rolling bearing increase the factors of influencing the supporting stiffness

    高速電主軸系統的轉速很高，通常都採用角接觸球軸承作為支承，由於滾動軸承的支承剛度呈非線性形式，特別在高速和超高速情況下，滾動軸承內部的動力學狀態十分復雜，由於滾動體運動所產生的離心力作用，使得影響其支承剛度的因素增多，不能作為常規的線性支承和普通的非線性支承處理。
  15. Nlgi service classification system a system of letter designations to define class of artomotive classis and wheel bearing greases

    Nlgi用途分類體系用於定義機動車底盤和車輪軸承潤滑脂分類的字母代號體系。
  16. Study on cold extrusion process of bearing body with inter and outer spline

    內外花鍵軸承體冷擠壓工藝研究
  17. Modification of sealing of the bearing body on model dg high - pressure boiler

    型高壓鍋爐給水泵軸承體密封的改進
  18. Sun hydraulik gmbh offers offers to screw - in valves, globe valves and valve housing

    提供軸承箱、軸承體、閥體、閥箱、閥套、閥門外殼及其它產品。
  19. Report back in the exhibit schedule : march 8, 2006 - 10 days am09 : march 10, 2006 - 12 days remove time : march 12, 2006 exhibitors range : car, car, motorcycle, light truck bearings, railway bearings, magnetic bearing spindle ; aviation aerospace marine bearings, rocket and satellite bearings ; industrial robot bearings, machining center and machine spindle bearings, textile machine bearings, motor bearings, and farm machinery bearings, paper machine bearings, bearings press, bearing mill, metallurgical mining, petrochemical machinery bearings, bearings sporting goods, marine rig bearing ; bearings, bearings gyroscope, high - precision bearings, high - speed bearings, linear motion bearings, needle roller bearings, thrust bearings, ultra - low - temperature bearings, special bearings, ceramic ball bearings, spherical with trophies bearing miniature bearings, quiet motor bearings, ball bearings, roller bearings, lubricating bearings corrosion resistant bearings, bearing joints ; bearing ring blank refinement, precision ball and roller crown, with nails cage

    撤展時間： 2006年03月12日參展范圍：轎車汽車摩托車輕型車軸承鐵路軸承磁懸浮軸承電主軸航空航天航海軸承火箭及人造衛星軸承工業機器人軸承加工中心及機床主軸軸承紡織機軸承電機軸承農機軸承造紙機軸承印刷機軸承軋機軸承冶金礦山石油化工機械軸承體育用品軸承海洋鉆機軸承組合軸承陀螺儀軸承高精軸承高速軸承直線運動軸承滾針軸承推力軸承超低溫軸承特種專用軸承陶瓷球軸承帶座外球面軸承微型軸承靜音電機軸承球軸承滾子軸承潤滑軸承耐腐蝕軸承關節軸承軸承套圈精化毛坯精密鋼球凸度滾子帶釘保持架軸承滾動體等軸承部件。
  20. Sencondly, an optimum model of mb is founded in order to make the parameters best. the principle of design is making the capacity of mb minimum in the condition of satisfying the maximum levitated force and temperature of coin below the permissible

    其次，為了得到最佳結構參數，對分子泵磁軸承結構參數進行了優化設計，建立了磁軸承結構設計優化模型，以磁軸承體積最小為優化目標，以線圈溫升小於允許溫升和承載力滿足載荷要求等為約束條件。
分享友人
分享到 Line

分享到臉書