軸承載荷 的英文怎麼說

中文拼音 [zhóuchéngzǎihé]
軸承載荷 英文
bearing load
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. The test must work in a specify rotation spectrum, temperature spectrum and load spectrum to analogize the reality condition

    實驗器要在一定的載荷譜、溫度譜、轉速譜條件下工作，模擬軸承的實際工況。
  2. The analysis calculation method for circular plates subjected to distribution load which is continuous and derivable and axial symmetry

    圓板承受連續光滑軸對稱分佈載荷的解析計算方法
  3. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  4. Since the preload and the friction moment of the geminate bearing are dominating factors affecting the performance of the navigation platform frame system, based on theoretical study on the control methods of bearing ' s preloads and frictional moment, the paper puts forward a method to control the preload of the twin bearings accurately. moreover, a multifunctional test apparatus of the navigation platform bearing is designed, and a lot of experiments of bearing ' s rigidity and friction moment and preload assessment are done

    考慮到成對軸承預載荷和摩擦力矩是影響導航平臺框架系統性能的主要因素，本論文對成對軸承預載荷及摩擦力矩控制技術進行了理論研究，提出了一種精確控製成對軸承預載荷的配對方法，設計了導航平臺軸承多功能測試儀，並對導航平臺軸承的剛度、摩擦力矩和預載荷評定技術進行了試驗研究。
  5. Roller bearings, load ratings and fatigue life for

    滾柱軸承額定載荷和疲勞壽命
  6. The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.

    為了避免劃傷，軸承上的最大負荷應該總是小於其卸載負荷。
  7. First of all, build the mathematics models based on the two different work condition : loaded on the axial loading ; loaded on combination loading

    首先，針對實際生產中不同工況，分兩種情況建立數學分析模型:主要承受軸向載荷;承受聯合載荷。
  8. Angle contact ball bearing can be subject to both radial and axial load, it also can be subject to pure axial load, its axial load capacity is depend on the contact angle and increased accordingly. it can be used for high speed and high precision application dueto high limit speed and pre - adjustable rigidity

    角接觸球軸承可同時承受徑向載荷和軸向載荷，也可以承受純軸向載荷，其軸向載荷能力由接觸角決定，並隨接觸角增大而增大，且極限轉速較高，剛性大還可預調，適用於高速、高精度場合。
  9. In chapter 3, the subgrid eddy - viscosity model for large eddy simulation is applied to calculate the three dimensions unsteady periodic turbulent flow in yantan francis turbine. the pulsating characteristics of some main physical parameters in flow field are found. the calculated axial water thrust of hydraulic turbine agrees with the model - test value

    第三章採用大渦模擬亞格子渦粘模型，對巖灘混流式水輪機的流場進行三維非定常湍流分析，得到了流場中各物理量的脈動特性，計算出ms的軸向水推力與模型試驗值大小相當；同時論證了對于下機架承重的混流式水輪發電機組可採用其推力軸承負荷作為水電站廠房振動的最大垂直激振荷載。
  10. Four pionts angle contact ball bearing is separable bearing, it can be subject to bi - directional load and have the function of both single row and double rows bearings

    四點接觸球軸承為可分離型軸承，可承受雙向軸向載荷，並有單列和雙列角接觸球軸承的功能。
  11. The basic stress-strain relations are defined with respect to an axially loaded member.

    基本的應力-應變關系是用承受軸向載荷的構件確定的。
  12. This type of bearings is separable, which can only carry axial load

    是可分離型軸承，只能承受軸向載荷。
  13. Research of load measuring device of oil film bearing used in high - speed wire rolling mill

    高線軋機油膜軸承載荷特性測試裝置研究
  14. In order to study the burning of the oil film bearing in high speed wire - rod mill, on - line tested temperature and operating mode of oil film bearing in a domestic framework of finishing mill f15 were determined and a large number of valuable test data were obtained

    摘要為了研究高速線材軋機油膜軸承燒損原因，對國內某高速線材精軋機f15機架油膜軸承載荷工況及工作溫度進行了在線測試，獲得了大量有價值的試驗數據。
  15. The single direction bearings of them can only carry axial load in one direction, while the double an carry alternating axial load in either direction

    單向軸承只能承受一個方向的軸向載荷，雙向軸承能承受兩個方向的交變軸向載荷。
  16. Rolling bearings - dynamic load ratings and rating life - methods for calculation of the modified reference rating life for universally loaded rolling bearings

    滾動軸承.動荷載額定值和額定壽命.普通荷載滾動軸承
  17. Four row circular cone roller bearings its performance and double row circular cone roller bearings basic same, but may withstand the bigger radial direction load and the two axle to the load

    四列圓錐滾子軸承其性能與雙列圓錐滾子軸承基本相同，但可承受更大的徑向載荷和雙軸向載荷。
  18. Axial bearing capacity of thrust roller bearing can be much bigger than thrust ball bearing and it can has high machining accuracy for its simple geometry and can prevent the dust, filth from invading as well

    推力滾子軸承比推力球軸承承受更大的軸向載荷，這類軸承的零件幾何形狀簡單，可以有很高的加工精度，可以防止灰塵、污物侵入。
  19. These bearings are featured by the extremely big axial load carrying capacity and mean while they can also carry cetrain radial load

    軸向載荷能力非常大，在承受軸向載荷的同時還可以徹骨你受干徑向載荷。
  20. There is stop groove in the bearing outer ring or it is simultaneously matched with snap rong

    使用在對軸承向限位精度要求不高又限們結構簡單的場合.不能承受軸向載荷
分享友人
分享到 Line

分享到臉書