載荷點 的英文怎麼說

中文拼音 [zǎihédiǎn]
載荷點 英文
point of load
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  2. With carbureted high - strength good - quality alloy, the series has the feature of high - efficiency and long life - span, high permissible axial and radial loads, low noise, high reliability and compact structure and so on configuration modality

    採用高強度優質合金鋼滲碳游淬火，具有高效率高壽命輪及高許用軸向，徑向載荷，運行噪音低，可靠性高，結構緊湊等優點。
  3. When reinforced concrete upper structure - piled raft - subsoil system is studied, every part of this system is looked upon homogeneous discrete space. accofding to static equivalent principle, equivalent node loads are calculated, and load embattle is integrated with element equivalent node force and directly bearing load

    在分析時，本文將鋼筋混凝土上部結構和地基、基礎的研究問題視為各向同性空間問題，且按靜力等效原則計算等效節點荷載，荷載列陣由單元等效結點力和直接作用於單元結點上結點荷載集成而得。
  4. Drop hammer rig was used to perform the impact experiment

    沖擊點位於中跨的中點，通過落錘裝置提供沖擊載荷。
  5. In the chapter 3, algor feas ( also called super sap ), a commercial fem software is introduced ; several. problems in building the finite element model of a auto frame is researched ; taking advantages of fem and mathematic programming, a strength analysis method of the frame of a series multi - spindle hydropneumatic suspension automobile is proposed ; taking the structure and load characteristic of a missile ' s frame into account, the static, eigenvalue and response analysis have been made by using super sap91

    第三章簡要介紹了大型有限元軟體sap91 ；對車架有限元建模及分析中的若干問題進行了討論；利用有限元法和數學規劃法相結合，提出了一種串聯多軸油氣彈簧懸架車輛車架強度分析的方法；針對某導彈發射車車架的結構和載荷特點，利用sap91軟體對其進行靜力分析、特徵值分析和動力響應分析。
  6. A statically indeterminate structure will usually sustain loads in excess of that at first yield before instability occurs.

    超靜定結構通常在失穩之前，既使超過第一個屈服點還能承受載荷。
  7. Find the load carried by each of the supports.

    求每個支點所承受的載荷。
  8. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  9. In this thesis, studies are focused on as follows : ( 1 ) based on analyzing the general transfer - matrix, the conception of the generalized double layer soil model is proposed, and the transfer - matrix ( r ) of half - infinite elastic mass is introduce - d to the analytic expressions of stress and settlement under the uniform circular, rectangular and strip vertical loads in multi - layered soil ; ( 2 ) according to the analytic expressions of the additional stress and settlement under unifo - rm circular in multi - layered soil, rectangular and strip vertical loads, the programs are develop - ed to resolve and debugged. the results show that the programs are correct ; ( 3 ) through calculating the coefficient of additional stress on the central axis of uniform circ - ular vertical loads, under the corner point of the uniform rectangular vertical loads, and on the central axis of uniform strip vertical loads, and the settlement on the center of uniform circular vertical loads and uniform rectangular loads in double - layered soil, the characters of stress and settlement are discussed ; ( 4 ) a case, as an example, is studied with different calculation methods, such as traditional theory, fem. the results obtained are compared

    本文在已有研究成果的基礎上進一步開展了以下幾方面的研究： （ 1 ）在對層狀地基傳遞矩陣法中的總傳遞矩陣分析的基礎上，提出了廣義雙層地基模型的概念，並把半無限體的傳遞矩陣r引入到多層地基在圓形垂直均布荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式中； （ 2 ）根據多層地基在圓形荷載、矩形垂直均布荷載及條形垂直均布荷載作用下附加應力與沉降的解析式，編制了程序，調試通過並驗證了其正確性； （ 3 ）通過對雙層地基圓形垂直均布荷載中心軸線上的附加應力系數和荷載中心沉降，矩形垂直均布荷載角點下的附加應力系數和荷載角點沉降及條形垂直均布荷載中心軸線上的附加應力系數進行的計算，探討了雙層地基中的附加應力與沉降特性； （ 4 ）應用本文的層狀地基體系理論對一個工程實例進行了計算分析，並與傳統的計算方法的計算結果和有限單元方法的計算結果進行了對比分析，結果表明利用層狀地基理論計算更能反映地基中附加應力分佈的實際情況。
  10. The dynamic force - displacement relation curve is of crucial important to the design and operation of mechanical impact devices. using one - dimensional wave mechanics and characteristic line theory, this paper presents a testing method for determination of dynamic force - displacement relation curve from one - point strain measurement on an elastic rod endface. the principle of measurement, data processing method and experimental results for penetration into granite are discussed. 4figs., 5refs

    沖擊載荷下彈性桿端的作用力-位移關系曲線是沖擊機械繫統研究的重要內容.基於一維波動力學方程，應用特徵線方法，探討了已知一點應變求取彈性桿端的作用力-位移曲線的測試原理與數據處理方法，以及在花崗巖上沖擊鑿巖機具的測試結果，對一點應變測試法的可行性進行了論證.圖4 ，參5
  11. Working loads and failure problems were analysized

    分析了焊接球罐的工作載荷及失效的特點。
  12. After the briefly present the origin and features of internet protocol version 6 ( ipv6 ), the paper detailedly introduced the conception, characters, security technologies of vpn, and main tunnel protocols used to implement and deploy vpns. after analyzing and comparing these technologies of realizing vpns, we choosed ipsec. then, the paper analyzed in the ipsec structure, function, work mode, and its components such as authentication header ( ah ), encapsulating security payload ( esp ), internet key exchange ( ike ), encryption and authentication algorithms, security association, security policy, and how they cooperate with each other in order to secure ip packages

    在簡要介紹ipv6協議的由來和優點之後，詳細闡述了虛擬專用網的概念、特點、安全技術及實現的關鍵隧道協議，通過對實現技術的分析比較，選用了安全性強大的ipsec隧道技術，接著深入研究了ipv6安全協議ipsec的體系結構、操作模式，詳細論述了ipsec協議簇的各個組成部分，如認證報頭ah協議、封裝安全載荷esp協議、密鑰管理ike協議、加密認證演算法、安全聯盟和安全策略等，以及這些組件之間如何協作，來共同實現對網路層ip數據包的安全保護。
  13. Base - load power is the minimum required to keep things ticking over ? the demands of three o ' clock in the morning, or thereabouts

    基本載荷功率是保持正常運轉的最小功率? ?凌晨三點所需的電能，或者與之相當的電能。
  14. Utilizing the characteristics of quick response, easy for automatization and easy to realize frequent commutation of the hydraulic system, this mechanism can be employed in composing the compound movement in horizontal and vertical direction, which could realize accurate simulation of the motion law for motorcycles and automobiles under the effect of random load in high frequency

    利用液壓系統反應快、便於自動化、易於實現頻繁換向的特點，該機構可用來合成水平、垂直方向的復合運動，實現對摩托車、汽車等在高頻隨機載荷作用下運動規律的精確模擬。
  15. From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

    針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。
  16. Following, using the experimental methods, the dynamic response of the stiffened conical shells under cosinoidal impulsive loading is studied. the changes of dynamic response of points along circumferential line of the conical shells are analyzed, and the characteristics of dynamic response of points are studied by both the time - domain analytic method and the frequency - domain analytic method

    採用實驗方法研究了加筋圓錐殼在側向餘弦載荷作用下的動力響應，分析了沿環向各點的響應變化，並從時域和頻域分析了它們各點的響應特性。
  17. In the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load

    針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。
  18. Abstract : in the light of the problems of the air balance system of model lcj1250 chain drive pumping unit, it is proposed to change the air balance with counterweight balance, and three criteria for the modification is put forward : ( 1 ) ensuring the reliability of the unit with smooth operation, low noise and long life ; ( 2 ) cutting down the production cost and using less component parts as possible ; ( 3 ) carrying out modification without such main technical parameters as stroke, pumping speed and maximum polished rod load

    文摘:針對lcj1250氣平衡式鏈條抽油機存在氣平衡故障率高和現場維修困難等問題，提出將氣平衡改造成工作可靠的重力平衡的方案，並確定了改造的三個原則：一是保證整機的可靠性，使抽油機運轉平穩，振動噪音小，壽命長；二是力求降低生產成本，減少零部件製造，盡可能選用原來的通用件，捨去平衡缸和空氣包等氣平衡附件，在原往返架主體上懸掛一個配重箱；三是力求不改變沖程、沖次及最大懸點載荷等主要技術參數。
  19. After igniting the motor, the combustion gas coming into the debond cavity may expand the debond cavity, and make an additional combustion area and lead to larger load

    發動機點火后燃氣進入脫粘腔，使脫粘腔變形並獲得額外的燃燒面積，從而導致更強的載荷。
  20. Load features of flight conditions on dynamic component of helicopter

    直升機某動部件飛行狀態的載荷分佈特點研究
分享友人
分享到 Line

分享到臉書