輥道電動機 的英文怎麼說

中文拼音 [gǔndàodiàndòngjī]
輥道電動機 英文
electric motor for rolling way
  • 輥 : 名詞[機械工程] （能滾動的圓柱形機件） roller
  • 道 : Ⅰ名詞（道路） road; way; route; path 2 （水流通過的途徑） channel; course 3 （方向; 方法; 道理） ...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 機 : machineengine
  • 電動機 : electric motor; motor （俗稱「馬達; 電滾子」）電動機並聯法 parallel connection of the motors; 電...
  • 電動 : motor driven; power driven; power operated電動擺 motor pendulum; 電動扳手 electric wrench; 電動泵...
  1. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  2. Explaining the main reasons why we should extend the timing range of the air - cooled transformational orbit electrical motor, this passage briefly introduce three feasible scenarios, and shows us the setting and steps to change the non - timing feedback system to timing feedback system when practicing the scenarios actually

    文章說明了風冷運輸輥道電動機擴大調訴范圍的主要原因，簡要介紹了三種可行方案，並說明了具體實施方案中，由無測速反饋方式改為測速反饋方式的設置及步驟
  3. We can realize the instrument control system and electric control system by using dcs and plc. the control system of reheating furnace is devided torol furnace area plc control system, roll plc control system and reheating furnace dcs control system. the controller of instrument and electric connect to the server of the operater station by the controlnet, by using dcs and plc, the technology of network and fieldbus technology to combine the process control system and process computer, intelligent instruments, drive system to realize the instrument and electric controll in one system

    採用dcs系統plc實現儀控和電控系統，把步進式加熱爐控制系統分為加熱爐爐區plc控制系統、加熱爐前後輥道plc控制系統、加熱爐dcs控制系統等三個子系統，儀表、電氣傳動用的控制器通過同一controlnet控制網與操作站的服務器連接，通過採用網路技術和現場總線技術，將控制系統與過程機、現場智能儀表和傳動設備連成一個整體，從而構成儀電一體控制系統。
分享友人
分享到 Line

分享到臉書