輪磨液 的英文怎麼說
中文拼音 [lúnmóyè]
輪磨液
英文
grinding fluids-
The slides are first cleaned ultrasonically several times in alternate baths of trichlorethylene and acetone, and are then scrubbed with a mildly abrasive detergent.
首先，把載片輪流放在三氯乙烯和丙酮溶液池中，用超聲清洗若干次，然後用一種中極的研磨去垢劑擦洗。Emhydr hr oils are based on high paraffin lubricant stocks compounded with rust and oxidation inhibitors and anti - foam additive to lubricate in hydraulic systems, plain and anti - friction bearings, enclosed gear cases etc. that do not require anti - wear or extreme pressure properties
Emhydr hr是以石蠟基基礎油摻配防銹、抗氧化與消泡添加劑製成，適用於工業液壓系統、減阻與平軸承、密封式齒輪等，以及不須抗磨與極壓性能的潤滑系統。Abstract : the effect factors of grinding roller surface roughness areanalyzed and experimented. the law of effect factors such as roller rotary speed, grinding wheel granularity, grinding liquid and so on, about roller surface roughness is obtained. the mathematical model of roughness is established through regression
文摘:對影響磨削輥面粗糙度的因素進行了系統分析和實驗研究，得出了軋輥轉速、砂輪速度、砂輪粒度、磨削液等因素對磨削輥面粗糙度影響的一般規律，利用回歸分析的方法建立了粗糙度的數學模型。From the experimental results, conclusions of particles " trajectories can be drawn for different densities and operating conditions. three axis segments were acquired, and three operating conditions were picked to study the distribution traits of particles inside the impeller under the different quality and concentration of the particles. based on the results, local wear of pump was forecasted and protecting measures were brought forward
得到運行工況對單個粒子運動軌跡的影響以及不同密度（質量）的單個粒子運動軌跡變化規律；沿水泵葉輪軸向取三個測量斷面，分別在三種不同運行工況下，研究各個斷面間（內）粒子分佈特徵，以及粒子質量和濃度對這種分佈特徵的影響；根據實驗結果，對輸送不同固液兩相流介質時，水泵局部磨損進行了預測並提出了一些防護措施。Effect of grinding fluid on grinding properties of vitrified bonded cbn wheel
砂輪磨削難加工材料時磨削液的作用It is not allowed to clean up cooling fluid and abrasive dust or to replace work - piece before the grinding wheel comes to a standstill
砂輪未完全處于靜止狀態時，不許清理冷卻液，磨屑或更換工件。Until now, there have been a few reports on the damage of the water pumps caused by sand and water cavitation. by use of the test loop for solid and liquid two phases, under the condition of 3 % head drop, the damage location and relative degree of the sand and water cavitaiton occurred on the impeller were tested and researched. the result was, them, compared with the results under the condition that water cavitation occurred and no cavitation but only wear occurred. the differencts were analyzed. the analysis result can be used as the basis of the further research and the improvement of the impeller shape
目前含沙水汽蝕對水泵損傷方面的報導甚少，本文利用固液兩相流試驗臺，對離心泵閉式葉輪在含沙水汽蝕時（ 3揚程下降點）的損傷部位和相對程度進行了試驗研究，並將此結果與清水介質發生汽蝕時的損傷情況[ 13 ]及含沙水無汽蝕情況下的磨損情況[ 7 ]相比較，對其差異進行了分析，為今後進一步探討葉輪損傷機理和葉型改進提供了實驗依據。Test method for indicating wear characteristics of petroleum hydraulic fluids in a high pressure constant volume vane pump
高壓定容葉輪泵中石油液壓液耐磨特性指示的試驗方法The foundation of back is10 steel or spcc, the surface is agglomerated by different trademarks copper and lead powder, resistant against : tiredness, abrasion, heat, has good carrying capability, especially, be the same with the connecting rod clevel, rocker, gear case, cranking motor, trig chasis, and motor gear case, redirector, hydraulic pressure oil pump, engineer
產品具有疲勞強度高，耐磨不發熱，承載能力大等特點，特別適用於汽車發動機的連桿搖臂，輪箱，起動馬達，制動底盤及摩托車輪箱，轉向器，液壓油泵，工程機械，空調壓速機等場合，目前我廠是國內最大的發動機連桿襯套生產企業之一。Wet grinding is adopted within the possible range if it cannot help, a spray or air will be blew and delivered. because coolant will have a lot of influence on the roughness of grinding surface, surface precision, wheel sharpness and wheel life
在可能范圍內採用濕式研磨為宜若不得已，加噴霧或空氣吹送，因研磨液對研磨加工面粗度表面精度砂輪銳利性及砂輪壽命都有很大的影響。Standard test method for indicating wear characteristics of petroleum and non - petroleum hydraulic fluids in a constant volume vane pump
定容葉輪泵中石油和非石油液壓液的磨損特性指示的標準試驗方法分享友人