輪緣應力 的英文怎麼說

中文拼音 [lúnyuányīnglì]
輪緣應力 英文
rim stress
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 緣 : Ⅰ名詞1 （緣故） reason 2 （緣分） predestined relationship 3 （邊） edge; fringe; brink Ⅱ動詞（攀...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  1. Compress disk is the very important rotational component in the areoengine. when the compress disk is working, the grads of temperature and stress between the rim and the center of the disk are great. in order to raise the thrust - weight ratio of the disk and reduce oil consumption. the best prospective way is the dual alloys disk used

    壓氣機盤是航空發動機上一個很重要的轉動部件，壓氣機盤工作時，輪緣和輪轂溫度梯度和應力梯度較大，為了提高飛機發動機推重比、減低耗油量，要求壓氣機盤的工作溫度、使用性能更高，雙合金盤製造是最有發展前景的技術。
  2. As the deformation caused by centrifugal force is beyond the small deformation range, the large deformation effect was also taken into account in the equation. two models are constructed, one is of shrouded blade and the other is of bladed disc. the static natural frequencies and dynamic frequencies ( under 3000rpm ) are calculated by the finite element method and cyclic symmetry technique

    針對葉片的結構特點，採用適應較強的三維八節點實體單元模擬葉片，建立葉片運動微分方程;葉片?輪盤系統在高速旋轉時，受到離心力作用，使葉片發生大變形，故在方程中考慮了幾何大變形的問題;為研究葉根輪緣之間的接觸狀態，建立了考慮葉根?輪緣接觸的有限元方程，利用拉格朗日增廣演算法來求解該方程，確定葉根輪緣之間的接觸面狀態。
  3. The paper forms the three information measures into measure vector as the input of cmac - cerebellar model articulation controller neural network and proposes a method of edge detection based on information measures and cmac. the edge contours generated by this method is very legible. the method has a high runtime performance and improves the resistance to noise

    本文將圖像的三個信息測度作為分量組成邊緣特徵的測度向量，作為小腦模型神經元網路? cmac的輸入，提出一種基於信息測度和cmac網路的邊緣檢測方法，用該法得到的邊緣輪廓清晰，實時性好，並且抗噪能力有明顯提高：將上述邊緣檢測方法應用於無人值守變電站，提出一種瓷瓶裂紋故障監控方案。
  4. After synthetically studying the effects of loading positions, rim thickness, circular pinion numbers and fillet radii of gear hob on root section stresses, a judging formula of plane stress and plane strain is proposed and verified, then 2d and 3d fem models are accurately established

    系統探討了加載位置、輪緣厚度、周向齒數的確定方法，分析了滾刀頂部圓角對齒根應力的影響，提出了兩類平面問題的判據並予以驗證。
  5. Many efficient methods were proposed for the strueture characteristics of the impellers and the wheel rims in the retrofit design, the detailed stress data at the weak points of the structure were obtained through the finite element method based on the plan selection of the normal strength calculation, and the safety of the newly - designed impellers was efficiently guaranteed

    改型設計中針對葉片、輪緣的結構特點，提出了多種行之有效的改型措施，並在常規強度計算對方案進行選擇的基礎上，通過有限元法獲得結構簿弱環節的詳細應力資料，有效保證了新設計葉片的安全性。
分享友人
分享到 Line

分享到臉書