輸出動作 的英文怎麼說

中文拼音 [shūchūdòngzuò]
輸出動作 英文
output action
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. The pneumatic - valve structure with simple, reliable operation, export thrust large maintenance convenient and inexpensive, such as fire blast merits pneumatic - valve widely used for chemical, oil, metallurgical, electrical, textile and other industrial production processes autopilot and remote control

    由於氣動調節閥具有結構簡單，動作可靠，輸出推力大，維修方便，防火防爆和價廉等優點，氣動調節閥廣泛應用於化工、石油、冶金、電力、輕紡等工業生產過程的自動調節和遠程控制中。
  3. This thesis primarily makes below the work of a few aspects : ( 1 ) the method to append the section line in the geological section plane and the geological plane graph intersected each other ; ( 2 ) the principle and method that automatic determinate of orebody on transverse section with the neural network theory was presented, and draw the slippery boundary of ore ; ( 3 ) the method that drawing the surveying well and lane way engineering in the geological and survey graph ; ( 4 ) the method to automatic calculation and statistics output ore reserves and grade ; ( 5 ) the method that automatic creating the geology cross section of the hole ; this thesis realizes automation for managing geological graph based on the substantive research work

    本論文主要作了以下幾個方面的工作： （ 1 ）提出了在相交平面圖和剖面圖中添加剖面剖切線的方法； （ 2 ）提出了應用人工神經網路理論確定剖面中礦體界線的理論和方法以及礦巖界線圓滑的原理與方法； （ 3 ）實現了礦山生產實測工程數據處理與地測圖件的有機結合； （ 4 ）實現了礦塊地質品位和儲量的自動計算和統計輸出； （ 5 ）提出了中深孔炮孔排面地質剖面圖自動剖切的原理和方法。本論文在大量研究工作基礎上，實現了地測圖件管理的計算機自動化。
  4. In typical watershed, quxi watershed, the result of external forcing, submerge and migrant, is the resource change of slope cultivated lands, economical forest, vegetation, water, habitant etc. of the ecosystem, and the changes of demand for food supplies, energy resource and education

    移民區典型小流域? ?曲溪小流域，受淹沒、移民2個驅動力的作用，耕地、經濟林、植被、水、棲息地等資源發生了顯著變化，系統的糧食、能源、教育需求也隨之而變，在內在反饋機制的作用下，導致系統輸出為水土流失加劇、生物多樣性受到破壞、土地退化嚴重等。
  5. And the interfaces have analog input, analog output and digital input / output. we have used differently cards, such as pc - 6330d a / d card, pcl - 728 d / a card based isa bus, ipc - 5375 i / o card and so on. in addition, we select micro - stir switches and pressure sensors as sensor elements to inspect the system and choose relays and induction valves to control the bicycle pump and the motor

    總線採用isa內部總線；介面主要有模擬量輸入介面、模擬量輸出介面、開關量輸入輸出介面等，課題分別選用pc - 6330d型a d板卡、基於isa總線的型號為pcl - 728的d a板卡、型號為ipc - 5375的i o板卡；另外，課題選用了微動式行程開關、壓力變送器作為傳感元件檢測系統，選用繼電器、電磁控制換向閥實現對氣缸、電機的控制；採用vc + + 6 . 0編制控制軟體，實現了纖維鋪放技術的計算機控制。
  6. After analysing several kinds of light - weighting structures through ansys, hexagonal speculum structure is confirmed. in the aspect of the controling of speculum, the paper adopts the brushless dc motor which is partial assembled to drive the point speculum and the inductosyn as angle measuring component is selected, the ad2s80a the system is used to get directly angle and angular velocity. double closed - loop speed and position control is designed, as the pid control is the well - developed algorithm, which can achieve stable rotation and precise position control

    在指向反射鏡的擺動控制方面，採用低速性能好的分裝式直流力矩電機作為指向反射鏡的驅動電機，並採用感應同步器作為角度測量元件，運用軸角轉換器ad2s80a進行角度和速度的輸出，採用技術成熟的pid控制方案，進行速度和位置雙閉環控制，以實現指向反射鏡轉動速度的平穩性和位置的精確性。
  7. Produce any multipage typeset file. can magnify or minify export at will, function of auto imposition to multipage small picture

    可製作任意多頁的排版文件，可隨意放大縮小輸出，多頁小幅面可自動拼版輸出。
  8. Carries created by ultra - fast laser pulse accelerate in the field of the photoconductor and form a transient photocurrent. the shape of the photocurrent lies on the movement of the carriers, as well as the movement of the carrier ' s lies on the field in the photoconductor

    光電導體中的載流子在光電導體內的運動情況決定了所輸出電脈沖的波形，而載流子的運動是在光電導體內部電場的作用下進行的，所以光電導體內的電場對光電導開關的性能有顯著的影響。
  9. First, this paper gives a method, which is utilized by baseband system according to wcdma system capability requirements, using asic + dsp to realize raker, using dsp + dsp to realize symbol process. the hardware structure of asic + dsp and dsp + dsp is designed from the whole design view. then, the discussion is made of the main function module of ic2001 and dsp, hi module, dsp peripherals on chip such as hpi, edma and emif

    文章首先結合wcdma系統性能要求提出了基帶系統所採用的方案，由asic + dsp實現rake接收機功能和dsp + dsp實現符號級處理功能;然後從總體規劃的角度設計出asic + dsp和dsp + dsp系統硬體結構，對ic2001和dsp的主要功能模塊， hi模塊， dsp片上外設hpi口、 edma和emif總線作了分析，並結合基帶處理功能開發了系統驅動;最後由信號源發出測試數據進入系統，進行功能實現后輸出數據繪制出波形圖，對所設計的基帶系統驅動方案進行驗證分析。
  10. The operation principleresult of saving power ， mate rial and reliability of ac and dc usual auto - converting saving power instrument are expounded, which the operation - coil of ac contactor given ac and dc voltage is usual, output is even dc, on and off and keeping voltage non - contactor auto - convert

    論述了與交流接觸器操作線圈適配的交直流輸入（操作）電壓通用、恆直流輸出、吸合與保持電壓無觸點自動轉換節電器的工作原理；接觸器配用節電器后的節能節材效果及節電器的可靠性。
  11. On top of one of the fast - opening ends that closed to the pig receiver & launcher shall assemble vent valve, safety valve and pressure gauge, and at the bottom shall assemble drain valve, sideway inlet and vent valve to take out medium from the main pipe as the power of forcing pig and conveyance medium

    靠近收發球筒快開盲板一端上部應設防空閥、安全閥及壓力表、下部設排污閥、側面設進、出油（氣、水）閥，以便從干管中取介質作為驅動清管器的動力及輸出介質。
  12. Designed sprag overrunning clutch is key component between output of gas jump - start engine and input of jet engine

    所設計的斜撐超越離合器作為燃氣起動機輸出與飛機大發起動輸入的關鍵部件。
  13. On the other hand, swain also claimed in the output hypothesis that as learners reflect upon their own target language uses, their output serves a metalinguistic function, enabling them to control and internalize linguistic knowledge

    寫作對閱讀有巨大的促動作用。 swain在其「輸出假說」理論中認為，必須經過大量的語言實踐活動，才能內化輸入的語言，最後達到習得語言的目的。
  14. Some standard process modules and standard therblig base had been created to improve the maneuverability of the outputs

    為了使輸出結果更具可操作性，建立了標準工藝塊和標準動素庫。
  15. It won t affect system s normal output, and it won t cause any conflict while serially connecting multiple protection locks

    不影響系統的正常輸出動作。且在同時串接多個保護鎖時，亦不會產生保護鎖相沖的情形。
  16. It won t affect system s normal output, and it won t cause cause any conflict while serially connecting multiple protections locks

    不影響系統的正常輸出動作。且在同時串接多個保護鎖時，亦不會產生保護鎖相沖的情形。
  17. While it works with supply voltages down to 1. 5v, the standby current is lower than 80n a together with the static power consumption lower than 240u w as well as the dynamic range of output voltages and currents is very wide

    模擬結果表明，電路工作於1 . 5v的低電壓時，靜態電流小於80 a ，靜態功耗不到240 w ，電壓輸出端和電流輸出端的輸出動態范圍大。
  18. The second one is how can we capture the data just before they are sent out or received in. the third one is how can we inform our monitor or debugger process this event, transfer the data to the monitor or debugger, and get the results back. as far as microsoft windows operation system is concerned, which mostly has been installed on personal computers and partly server cmputers, softwares access data in internet through windows socket application program interface

    就被廣泛安裝在個人計算機和一部分服務計算機的微軟視窗操作系統而言，軟體通常通過操作系統提供的套接字網路介面訪問網路數據，在視窗操作系統上有兩套網路介面，一是由伯克勒大學設計，被稱之為bsd套接字的介面，由阻塞同步和非阻塞異步以及輪循機制控制輸入和輸出工作;另一套是微軟公司開發的窗口套接字，由網路消息事件驅動。
  19. According to the at minicar project of chongqing changan automobile co. ltd., a series of researches have been carried out. base on the characteristic tests of engine and torque converter, the mathematical models are established using curve fitting

    在發動機性能試驗與液力變矩器性能試驗的基礎上，採用曲線擬合的方法得到了發動機及液力變矩器的數學模型，並對兩者聯合工作的輸入、輸出工作特性進行了分析。
  20. There were two main roles of the imperial college of tang dynasty in the sino - foreign cultural and educational export : to enroll and cultivate overseas students by spreading confucianism and its culture, induding a whole set of rules derived from confucianism and knowledge related to calligraphy, mathmatics, music and literatare ; and to participate in important national foreign activities to spread and export confucianism by means of deferring confucius

    摘要唐代國子監在當時對外文化教育方面的作用主要體現在兩個方面：第一，招收和培養留學生，主要承擔著儒家思想和文化的傳播與輸出工作，包括在儒家思想和文化之下衍生出來的一整套完整的制度，以及有關書法、數學、音樂、文字學等方面的具體知識；第二，參與主持國家重大的外事活動，通過對聖賢的景仰傳播與輸出以儒家禮儀制度為代表的儒家文化和思想。
分享友人
分享到 Line

分享到臉書