輸出裝置定位 的英文怎麼說

中文拼音 [shūchūzhuāngzhìdìngwèi]
輸出裝置定位 英文
output device positioning
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 裝 : Ⅰ名詞1 （服裝） dress; outfit; attire; clothing 2 （演員的化裝品） stage makeup and costume Ⅱ動詞...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  • 裝置 : 1 （機器設備的配件）installation; device; apparatus; equipment; arrangement; gear; appliance; rig...
  1. The metal nanoparticles that form in hot critical layer are drawn from reaction area and arrives designated installation via the centrifugal selection grades ware under the transport of inertia gas current, then metal nanoparticles are collect via filter completion

    氣流將在熱臨界層中形四川大學博士學位論文成的金屬懸浮顆粒從反應區中提取出來，經過離心分級器的篩選，在惰性氣流的輸運下抵達指定裝置，通過濾器完成對金屬納米顆粒的收集。
  2. Based on the analysis of designed cad graphics and the given parameters, computer can convert the cad graphics to a acdbpolyline which can simulate the routine of the conveyor chain. then by using the method of point - by - point strain calculation, computer could figure out each point ’ s strain of the chains under different load states, and get the results such as strain ’ s maximal and the minimal values and their positions, weight of the strain equipment and power of the drive electric - machinery that the conveyor need

    通過對設計的cad圖形和給定參數的分析，將輸送鏈運行軌跡轉化為一條可模擬輸送鏈軌跡的多義線，然後用逐點張力計演算法動態地計算出各種加載狀態下輸送鏈上各點的受力，得出最大、最小受力點的力的大小和位置，拉緊裝置的重量，驅動電機所需的功率等結果。
  3. The papers also brings forward the design parameters of the material critical suspending speed and the wind capacity according the theory of the air transportation, analyses and build up the condition of material diameter and airflow speed of the gas - solid current locating the separating interface

    論文根據氣力輸送理論求出螺旋氣力吸取料裝置物料的懸浮速度及風機風量的設計參數，分析確定位於分離界面處的氣固二相流處于層流狀態即處于粘性磨擦阻力區的粒徑條件與氣流速度條件。
  4. The structure of this magnetic inducting crankshaft position sensor assembly is simple, reliable easy for installation and use, being a crucial part of electronically controlled engine. as one of the important input signal of ecu controller, the sensor assembly can transmit stable cranking signal under any rotating speed of engine and ensures the stability of the performance of electronically controlled engine in respect of oil consumption, exhaust and output

    該磁感應式曲軸位置傳感器總成結構簡單，工作可靠，安裝使用方便，是電控發動機重要關鍵的部件作為ecu控制器重要的輸入信號之一，該傳感器總成能在發動機任何轉速輸出穩定的曲軸角度信號，可確保電控發動機在油耗排放輸出功率方面的性能保持穩定。
  5. Methods for the field measurement of the sound output of audible public warning devices installed at fixed locations outdoors

    室外固定位置安裝的公共音響警告設備的聲音輸出現場測量
  6. The inertia power was analyzed during the freightage in the article, and according to the results ; the rope lug was designed, the roof wooden structure was optimized. especially aiming at some problems of the quality of the sample surface and the reliability of the door lock ; some effective measures were introduced ; the brake system was changed with stainless steel pipes, and the fitting location of the brake setting was adjusted

    文中詳細分析了貨物在運輸過程中產生的慣性力，以此為依據設計了固定貨物的繩栓；優化了車頂木結構、針對樣車在外觀質量和門鎖可靠性方面存在的問題，提出了對應的改進措施，並改用了不銹鋼制動管系，調整了空氣制動裝置的安裝位置。
  7. The conventional rectifiers produce harmonic problem in power system. while three - phase pwm voltage source rectifiers ( vsr ) can provide constant dc bus voltage and get low harmonic distortion of input current. it also has line power feedback capability

    傳統的整流裝置是電網污染的主要來源，三相電壓型pwm整流器具有輸出電壓恆定、能實現單位功率因數運行的特點，甚至可以實現電能回饋電網。
分享友人
分享到 Line

分享到臉書